Questions

Window won't start after install new RAM

Tags:
+
0 Votes
Locked

Window won't start after install new RAM

bchen521
My computer currently has 1 GB of DDR2 800 memory and I want to upgrade it. I bought 2 GB of new RAM (same speed) and installed it. On the boot screen the memory test passed. (it show I have 3 GB RAM now) but my window won't start.(I am currently using Vista) The computer just hangs there even in safe mode.. Once I remove my new RAM the computer works perfect again.. Will someone tell me what might be the problem here? My mobo is not that old so it should support 3 GB RAM... help.
Thanks a lot!
  • +
    0 Votes
    Langlier

    1. Bad RAM
    2. Bad RAM slot
    3. New ram not really the same speed as old ram.
    4. Motherboard wants to run in dual channel mode and the new RAM is conflicting (try removing the old ram and use the new ram in the proper (normally different colored) slots. Dual channel needs matched pairs of ram.

    5. Unsupported size/speed of RAM

    +
    0 Votes
    bchen521

    Thanks a lot for your reply.
    I have a question regarding your comment on dual channel mode. You said "new ram in the proper (normally different colored) slots"
    I have 4 slots, 2 red and 2 blue, and my ram comes in pair, so I should insert them into the slot with SAME color right? This is what I did, my old RAM (1 GB, 2 x 512 RAM) was inserted into the 2 blue slots, and I inserted my new RAM (2 GB, 2 x 1 GB RAM) was inserted into the 2 red slots. Is it correct?
    I think my motherboard wants to run in dual channel mode.

    Thanks a lot for all your help!

    +
    0 Votes
    Langlier

    some of them like to have one chip in each color some like to have the same chips in the same color. If you have your motherboard manual it should tell you in there or the information should be avail on the manufac website.

    +
    0 Votes
    ben.vdwesthuyzen

    Hi I have the same problem. I had 2 Gig of ram in my system and the moment I add anothre 1 gig (= 3Gig), Vista doen't boot. XP will work fine. If I remove the 1Gig (=2Gig), it works fine. There must be a problem with Vista, cause the hardware checks out fine. I'm using Vista Ultimate Edition.

    +
    0 Votes
    ben.vdwesthuyzen

    Hi. I found the problem.
    Vista.. Stupid Thing.
    If you add more than 2gig ram, it doesn't start, because the system Max Default is 2048. So the moment you exeed this, it doesnt work. So this is what you do.
    1. Add enough ram, so that Vista can boot up (No more than 2 Gig ram)
    2. Go to Run and type in MSCONFIG and press enter.
    3. Good to BOOT and then ADVANCE OPTIONS
    4. Tick Max Memory and make it the amount that you will have after you have added your new ram.
    eg:
    3gig = 3072
    4gig = 4096
    and so on and so on

    Hope this will help you.

    +
    0 Votes
    aldwin0427

    i have tried your suggestion ben i i have 512mb max memory and when i tried to set it up to max it always goes back to 512 after clicking ok...

    +
    0 Votes
    greaser

    When I try to update my max memory it defaults back to 1792. Anybody know whats up?

    +
    0 Votes
    ComputerCookie

    Some info about the MB and RAM might help!

    +
    0 Votes
    OldER Mycroft

    1792MB + 256MB = 2048MB.

    Can a mobo have 256MB onboard graphics?

    If he had 1GB RAM he'd only have 768MB system RAM.

    Only a guess - until confirmation.


    <Typo>

    +
    0 Votes

    New motherboards and ram memory.
    The new motherboard that you have will only take memory in PAIRS, so replace the new ram but leave out the 1gb ram. If it will not bootup then take out just one memory chip and place it in another slot, keep doing this if you still have problems booting, in the end the memory will kick in and your computer will bootup. The other thing is when you place the new memory on your board make sure you click on "Load default drivers" in the bios this will make sure your memory talks to the rest of the system (sort of). When it is working ok then go back into your bios and reset the dvd/cd, hdd, floppy drive to the way you had it before. Hope this helps you out.

    Please post back if you have any more problems or questions.

    +
    0 Votes

    On to your motherboard. But in pairs only.

    Please post back if you have any more problems or questions.

  • +
    0 Votes
    Langlier

    1. Bad RAM
    2. Bad RAM slot
    3. New ram not really the same speed as old ram.
    4. Motherboard wants to run in dual channel mode and the new RAM is conflicting (try removing the old ram and use the new ram in the proper (normally different colored) slots. Dual channel needs matched pairs of ram.

    5. Unsupported size/speed of RAM

    +
    0 Votes
    bchen521

    Thanks a lot for your reply.
    I have a question regarding your comment on dual channel mode. You said "new ram in the proper (normally different colored) slots"
    I have 4 slots, 2 red and 2 blue, and my ram comes in pair, so I should insert them into the slot with SAME color right? This is what I did, my old RAM (1 GB, 2 x 512 RAM) was inserted into the 2 blue slots, and I inserted my new RAM (2 GB, 2 x 1 GB RAM) was inserted into the 2 red slots. Is it correct?
    I think my motherboard wants to run in dual channel mode.

    Thanks a lot for all your help!

    +
    0 Votes
    Langlier

    some of them like to have one chip in each color some like to have the same chips in the same color. If you have your motherboard manual it should tell you in there or the information should be avail on the manufac website.

    +
    0 Votes
    ben.vdwesthuyzen

    Hi I have the same problem. I had 2 Gig of ram in my system and the moment I add anothre 1 gig (= 3Gig), Vista doen't boot. XP will work fine. If I remove the 1Gig (=2Gig), it works fine. There must be a problem with Vista, cause the hardware checks out fine. I'm using Vista Ultimate Edition.

    +
    0 Votes
    ben.vdwesthuyzen

    Hi. I found the problem.
    Vista.. Stupid Thing.
    If you add more than 2gig ram, it doesn't start, because the system Max Default is 2048. So the moment you exeed this, it doesnt work. So this is what you do.
    1. Add enough ram, so that Vista can boot up (No more than 2 Gig ram)
    2. Go to Run and type in MSCONFIG and press enter.
    3. Good to BOOT and then ADVANCE OPTIONS
    4. Tick Max Memory and make it the amount that you will have after you have added your new ram.
    eg:
    3gig = 3072
    4gig = 4096
    and so on and so on

    Hope this will help you.

    +
    0 Votes
    aldwin0427

    i have tried your suggestion ben i i have 512mb max memory and when i tried to set it up to max it always goes back to 512 after clicking ok...

    +
    0 Votes
    greaser

    When I try to update my max memory it defaults back to 1792. Anybody know whats up?

    +
    0 Votes
    ComputerCookie

    Some info about the MB and RAM might help!

    +
    0 Votes
    OldER Mycroft

    1792MB + 256MB = 2048MB.

    Can a mobo have 256MB onboard graphics?

    If he had 1GB RAM he'd only have 768MB system RAM.

    Only a guess - until confirmation.


    <Typo>

    +
    0 Votes

    New motherboards and ram memory.
    The new motherboard that you have will only take memory in PAIRS, so replace the new ram but leave out the 1gb ram. If it will not bootup then take out just one memory chip and place it in another slot, keep doing this if you still have problems booting, in the end the memory will kick in and your computer will bootup. The other thing is when you place the new memory on your board make sure you click on "Load default drivers" in the bios this will make sure your memory talks to the rest of the system (sort of). When it is working ok then go back into your bios and reset the dvd/cd, hdd, floppy drive to the way you had it before. Hope this helps you out.

    Please post back if you have any more problems or questions.

    +
    0 Votes

    On to your motherboard. But in pairs only.

    Please post back if you have any more problems or questions.