Question Locked

added ram and now cp won't turn on

0 helpful
15 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

So I decided to add 512mb ram to my hp pavilion
523n desktop which previously had a 256mb and
512mb sticks in it in order to help speed
things up but now that I added the new 512 with
the previous 512 RAM it won't start up at all.
I tried going back to the previous RAM and that
won't work either. Any ideas? Help please.

15 replies

by rob miners

Install your new RAM and try this. If both of these suggestions will not work with the new RAM try going back to the Old RAM.

Hp Compaq BIOS Reset

Resetting and updating the BIOS

In case an item was changed in the BIOS, such as the primary display device setting, use the following steps to reset the BIOS back to its default configuration:

Turn on the computer and press the keyboard key that enters the BIOS Setup screen key when the keyboard light comes on. The key to enter the BIOS should be one of the following:

HP and Compaq desktop computers that came with Windows Vista, press F10 .

For HP Pavilions desktop computers that came with Windows XP or previous versions of Windows, press F1 .

Compaq Presario desktop computers built after 2002, press F1 .

Compaq Presario desktop computers built prior to 2002, press F10 .

Wait 5 seconds.

Press the F5 key to restore the default settings of the BIOS.

Press Enter to accept the change and wait five seconds.

Press the F10 and then the Enter key to save the changes and exit from the BIOS.

If you still have no success try Clearing the CMOS settings. The Jumper is next to the Battery.

The 3-pin CLR jumper allows you to clear the date, time, and system setup parameter memories in CMOS. The onboard button cell battery powers the RAM data in CMOS, including system setup information.

CAUTION: Do not change any jumper setting while the computer is on. Damage to the motherboard can result.

Turn off the PC and unplug the power cord.

Move the CLR jumper cap from pins 1-2 (normal) to pins 2-3 (clear CMOS).

Keep the CLR jumper cap on pins 2-3 for 5 to 10 seconds, then move it back to pins 1-2.

Plug in the power cord and turn on the PC.

Enter the BIOS setup to change the BIOS settings.

Keep us informed as to your progress if you require further assistance.

If you think that any of the posts that have been made by all TR Members, have solved or contributed to solving the problem, please Mark them as Helpful so that others may benefit from the outcome. ;) :D

by kyle_serres

I cannot use that help because the computer
will not turn on at all. I tried to go back
to the previous RAM too but it still will not
work. When I plug in the power cord, the
green PCS light comes on to show it is
getting power, but when I hit the power
button to turn the cp on that light goes out.
That is the only sign of anything that is
happening when I try to turn on the computer.
Nothing else really happens. Any ideas would
be greatly appreciated.

by rob miners

Start by turninig off the power to the PC from the wall and remove the power lead from the PC. Remembering to ground yourself by getting into a position that will allow you to access the components without moving your feet and putting the back of your hand on the PSU after you have removed the PC's Cover. By not taking this precaution it is possible that you could inadvertantly cause damage to the PC from an electrostatic discharge. Disconnect the 20-24 pin power connector from the motherboard. Reinsert the 20-24 pin power connector to the motherboard.
Reconnect the power and turn on the PC.

Check the power light on the power supply unit at the back of the PC.

by Former member

And then switch on your computer, you might hear a few beeps. Do a shutdown and replace your RAM and make sure that you put the ram at an angle and then push down firmly, do the same to the other stick of ram.
Now try and see if it boots up.
When it does go into the bios and select "load default settings" (you can change this later).

Please post back if you have any more problems or questions.
If this information is useful, please mark as helpful. Thanks.

by kyle_serres

Ok, so I took out all the RAM and tried to
turn on the computer like you said but it
still is doing the same thing. It won't turn
on at all, no beeps or anything. Just that
same green light on the power cord supply
goes out when I try to turn it on. Any ideas
as to what that means?

p.s. thanks so much for the help so far. I'm
really in a bind and I appreciate this a lot.

by mjd420nova

And it wouldn't boot either?? Sounds like you may have fractured one of the RAM connectors or jammed some foreign object in the slot.

by kyle_serres

And what would the consequences be if that is
what the problem is? My motherboard messed up
then?

by mjd420nova

In most cases, it's the plastic frame around the connector or the hold down clips that get broken. Check with the mfgr of the MOBO to see if they have replacements available, otherwise it will beed to be repaired. With a good magnifier/lamp and a low wattage soldering iron and a steady hand, it could be replaced. In most cases, it would cost as much to be repaired as repalaced unless it is priced over $150. then it would be better to repair, if you can find a service center willing to tackle the job. I've done quite a few myself but they were throwaways and I took them in as junk and did it myself. Some required a complete replacement and others were had rams that were forced and had broken platethru holes that took some very tedious trackdowns and extra money to buy the print diagrams to aid in continuity testing.

by kyle_serres

Ok, I disconnected the power connector then
reconnected it and it still won't turn on.
The power light on the power supply unit at
the back of the PC comes back on until I try
and turn the power back on and then it just
turns off again. Does this mean that I might
of caused damage to the PC by accidentally electro statically shocking it? Because it
won't turn on at all now and it is quite
frustrating. Thanks for the help so far, any
more would be so wonderful. Thanks

by rob miners

fans spinning up at all. HP's troubleshooting page for psu problems

http://tinyurl.com/yrvu68

I would give the inside of the case a blowout with compressed air. When blowing air through the fans make sure that you physically stop them from spinning, as they may generate power and blow something up. Remembering to ground yourself by placing the back of your hand on the Power Supply Unit and not moving your feet. By not taking this precaution it is possible that you could inadvertantly cause damage to the PC from an electrostatic discharge. Then remove the Heatsink, giving it a thorough clean and reseat the CPU applying new CPU grease. If the Fans spin freely when you give them a spin they are probably OK. If there is resistance replace them.

Clean the golden edge of each memory stick with a soft rubber/eraser, remembering not to touch the golden edge of the memory stick. Check with one stick at a time, remembering to disconnect the power from the PC.

Keep us informed as to your progress if you require further assistance.

If you think that any of the posts that have been made by all TR Members, have solved or contributed to solving the problem, please Mark them as Helpful so that others may benefit from the outcome. ;) :D

by kyle_serres

alright I got it up and running again! I took
out my power supply and fixed it up and
cleaned out the fans like you said and now
it's starting up. And I think the voltage
selector switch was on the wrong setting for
some reason. So thanks so much for the help.

by kyle_serres

Ya my connectors look fine, but would my PC
not be starting up at all due to something
being wrong with the motherboard, like it
getting electric static? I just
can't figure out why it wouldn't start at
all...

by Former member

Get another power supply adapter and try that.

Please post back if you have any more problems or questions.
If this information is useful, please mark as helpful. Thanks.

This discussion is closed to new replies.