Discussion Locked

Arghhhh...ten minute repairs that take an hour

0 helpful
13 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

After finally cleaning the workbench so I can see it, I decided to drop a new motherboard into an old PC. A ten minute job.

Tested the power supply / mobo on the bench, worked fine. :)

Put motherboard/PSU in case, hooked everything up, and it won't power on (UGH). :(

Unplugged everything, nope. :(

Pulled mobo out of case, it powered up.

Slapped some electrical tape on mobo where screws go in, mobo back in case, nope.

removed motherboard, it works.

Inspected power supply connector, touched up solder connections, put mobo back in, nope.

with mobo powered up, put mobo into case....mobo shut off half way there! :{

jiggled power supply connection, mobo shuts off...hmmmm.

inspected power supply connection...looks fine.

gently tugged all wires of PSU connection...AHA :)...black/brown wire breaks off in hand..

Extract pin from connector, resolder wire, done. v/

One hour later, new mobo installed.

13 replies

by nicknielsen

That if you had tested the PS while in the case, it would have passed because the wire was bent in the right direction. :D

Had a printer pull the progressive failure routine today. The initial call was for persistent random paper jams. What I found was constant paper jams in tray 2. Checked the mechanics: the feed roller is loose and not making good contact with the idler roller, so not pulling the paper. Replaced the bad tray assembly, printed a couple of test pages, and put the printer back in service.

I wasn't even back to the van when they called me back in for a paper jam at the fuser entry. Cleared it, printed a test page, jammed.

Replaced the toner cartridge, printed a couple of test pages, and put the printer back in service.

As I was walking out the front door of the store, I was paged. More paper jams.

Pulled the fuser, cleaned it, put it back in and ran a good function check, so printed a couple of test pages, and put the printer back in service.

As I was walking out the office door, I heard the beeps. I continued on to the van, got a fuser, went back in and replaced it.

Should have been a ten-minute job. An hour-and-a-half later... X-(

by gsg

A vendor, while looking at a problem on a system, deletes the equivalent (if printed) of 10,000 pages of medical data. What was their answer? Sorry. We can't recover that for you, you'll have to do it.

I had to write a program to recover it, spend over 15 hours babysitting the program, and crashed a server twice recovering the stuff.

Unfortunately, backups didn't help. This was all stuff in a virtual print queue and arrived there between backups.

15 hours worth of work on my part = non-payment of maintenance contract for april, plus charging the vendor for my time at time and a half.

2 seconds to click the mouse = priceless.

Edited to add: all data was recovered and no patients were harmed. The tech support person from the vendor is expected to recover as soon as my foot is removed from her @$$.

by the scummy one

I have brought this up before (including when it happened).
We had a single share for the dept. Each group had their own sub folder on the share, with it's own permissions. NOTE: there IS confidential data on the share.

Anyway, the IT group decided that (without warning) all shares should have 1 set of permissions, and should not have sub-folders with individual permissions. The share owner had transferred to another group, and never passed ownership of the share, however, still proclaimed that he had never received any notice that the share would be down while everything was transferred to a new server.
We were all surprised when the share was suddenly unavailable. However, we quickly found out why, I sent a notice to the dept. and all was OK.
After it came back online, everyone was able to work, so I never gave it any thought. However, almost 2 weeks later, I received a call from someone, that they were on the share and hadnt been in Legal for 10 years. I quickly found the problem (she hadnt been removed from the global group). Remedied, a new task -- go through the Global Group and look for other problems. However, while scouring the GG, I ended up in a netmeeting with someone, who should have access to a specific folder, but not others. This person stated that they had accidentally clicked on the wrong one (with confidential data) and it opened. Looking into it, this user had access to everything :0
so I had another user look, same thing :0
I looked at the permissions for the site, which should have been restricted at several levels with more than 20 GG's assigned at different levels and all at the top level. Furthermore, some of the folders were supposed to remain read only except for individual permissions. So, what did IT in it's infinite wisdom do -- assigned (not even authenticated users) Everyone -- read/write and all inherited permissions for all sub folders.
So, anyone who knew about the shares could access them unrestricted. Now, in Legal we often have outside council and business partners and they may have limited access to some of these shares :0 So, others did know about the shares (however we never got an access report for it.
Anyway, I spent half a day with IT telling me that they cannot do anything, nor can they restore permissions because it was now against the policy. After 5 people, I figured this was the wrong approach. I sent this up the management chain, while working the proper channels for IT, and I had decided back channels were needed as well.
Before I could get anywhere on the first 2 channels, I found someone that was willing to help (temp). He could not do much, but he was able to remove all permissions from the shares, and give me individual full control permissions.
Finally, something is starting to work, however, I had no idea what groups were assigned to what folders :0 So I had to spend a few days contacting people (and having them figure out who needed what access where) and re-did the groups -- so far, lots of downtime for the entire department, and lots of leg-work. During this time the management chain finally got things together and forced IT to help. However, they only agreed to do a bare minimum (make me do everything, and if I have problems, they may step in and assign permission). Furthermore, yet another new project -- within 1 month I had to split the sub folders to individual shares to stay in compliance with the new policy and transfer the data from one share to another (they wouldnt do a server to server transfer or anything -- the datacenter is half way across the country).

So, I spent over a day in the office and the entire weekend through a vpn re-assigning permissions (hours with some of the sub folders).
Finally, it was done -- permissions were set for almost all of the shares, however I still needed to find out about a few of them, but the main emergency was over and the dept was functional again.

overall, it took over a week and a half, and IT wouldnt even backup our share (old or new) and send us a copy, so I setup 2 systems to download the entire contents of everything right after I put it in read only (planned) and right before I ran the transfer (another weekend + more).

I never bothered to count the time it took from me alone, let alone each group in the dept + downtime because records or other info was unavailable. And this does not even bring up any costs involved if any data was compromised.

Edit: And all because IT screwed up and wouldnt help correct the problem. All they had to do was temporarily put the old server(s) back up until we created the new shares and had the data transferred server to server.

by av .

Its such a good feeling to get technology to work like its supposed to. Its not easy, but when it works, its the greatest.

AV

by seanferd

I won't even try to obfuscate my original verbalization upon reading your post. "Unprintable" will have to cover it.

IT, Nice Worrrrk.

As an aside, what was the total time involved in getting your new TV fixed? ]:)

by the scummy one

but I finally took them back, picked up a 46" Samsung and have liked it much better (no problems). It took about 2 months, but I wasnt working on it constantly

by .martin.

a DVD drive in a NEW computer not working (not ejecting)

THEN it decided it would not connect to the internet...

by hal 9000

The first one was a call out on a Sunday Mourning to a computer listing a Imminent HDD Failure. Got to love the SMART. Anyway sure enough the HDD was on it's way out so I shoved in another one Cloned the Old Drive over to the new one and was about to leave when i was asked to deploy SP1 for XP. I tested with the compatibility tool and it should have been a easy though slightly longer than 10 minute job so I grabbed the Downloaded SP1 File that I had used previously and ran it.

Everything went fine till the restart then I was greeted with a No Operating System Found message and sure enough the HDD was now blank. Cloned the Old HDD again and this time I disconnected the CD Burner before applying SP1 but the result was still the same.

5 Days latter and Gog only knows how many clones I discovered that the DVD ROM which was SP1 Ready wasn't so if I had of left the CD Burner connected and lost the DVD ROM it really would have been a short job. That was another answer that I had for M$ to add to their lists.

Or worse still a new system that I built for the CEO of a company worked fine for 3 days then it reported No OS Found. The only thing changed was that a HP SCSI Scanner had been added and the HDD was really blank but as there was no Backup I had to recover the Data before I could proceed any further. 2 days latter I returned the reloaded system and made sure that it was working properly. Another 3 days latter No OS Found again.

This time I recovered the Drive again as it had a couple of days Data that wasn't backed up and ran it for a week without so much as a hiccup occurring then returned it. Again 3 days latter a No OS Found message and another Blank HDD.

So this time I took steps to find out what was really happening but only after I tried to crawl down the Phone and kill the rep from HP who was insisting that it only took 20 Minutes to rebuild their Software and get their scanner working. I had by this time worked out that the scanner was involved and caused the problem though I had no idea of why this was happening just that it was for some reason.

Anyway no matter what I tried I couldn't get the system to fail in any manner and I really abused it for several weeks with all sorts of nasty things thrown at it. But no matter what I could think of I couldn't find a reason why this was happening. Anyway after this happened several more times I eventually got the CEO give me a mouthful for the Faulty System that I has supplied and I found his new Digital Mobile Phone under the SCSI Scanner lead. The Light went on in a big way at that point and I had him place the phone in a different location after I returned the again rebuilt system.

It worked perfectly for ever more after he realized that placing the Cell Phone there under the Unshielded SCSI Lead was what was causing the problem but he of course had to prove this to himself and do it again so I had yet another rebuild. :(

OH did I mention that every trip there was a 85 KM trip one way? Not to mention Hours of wasted effort rebuilding the system. I did supply a Shielded SCSI Lead and I did suggest a different Scanner to prevent this happening but as they already had the hardware they wanted to use it so I was stuck with it on a otherwise perfect system. Naturally I got the blame because I supplied a M'Board with On-board SCSI so they had to use that Cheap HP Scanner that he saw in a shop one day and as this was the best system in the building everyone wanted to use it for whatever they needed. Thankfully when he adopted a NB I never had another problem. ;)

Col

by the scummy one

and when the disk showed up as empty/blank, put in a Linux cd and ran an NTFS repair :0

Ok, it doesnt work that well, but it does work sometimes

by hal 9000

I still get a laugh out of thinking of the Office Manager at that place who took the phone off me and tried to calm me down when I was speaking to the Person from HP who was insisting that I didn't know what I was doing as it only took 20 minutes to install their Scanner Software. :D

Or another one but it's very old and happened when DOS was new. I got new 286 in for a Reload of DOS and the Menu Program that I used for that company. Wasn't anything special but it looked nice and worked.

Anyway they wanted M$ DOS not DR DOS which I was then using exclusively because it was better. I loaded the first M$ DOS Floppy and got a [b]Device 6 Missing[/b] error message, which I just had to look up to find out what it was. Something as specific as that just had to be an easy fix right? In their Printed Junk M$ didn't list a Device 6 and by now I was more than curious so I rang Tech Support for M$ and asked. [b]Big Mistake[/b] that was.

After 3 hours on the phone the head of the department eventually found a reference to Device 6 somewhere and told me that I had forgot to fit the CPU as that was what Device 6 was. So being the poor fool that I am I just had to ask how M$ could write an application that didn't require a CPU to be present and still allowed a error message to appear on the screen. :^0

I never did get a reasonable answer to that question and I have never found out what Device 6 actually is. ;)

Col

by gsg

I'm floating along on my satisafaction that as of yesterday, we no longer use this company. OK, in all fairness, we've been working for the past 8 months to replace the application, but revenge is still sweet.

Oh, and I got a nice thank you letter from the CIO in my HR file, along with some gift certificates to a local movie theater. She knows that I'm breathlessly waiting for the new Star Trek, Harry Potter, and Transformers movies.

by the scummy one

I decided it was time to rebuild a few systems yesterday. They have been acting up, so I completely wiped the drives. I decided that the image disk that I was using was old (3 months) and there was a new version available. So, I spent 5+ hours downloading it (yes, the network is that slow) yesterday. Today, after the rush of stuff to do I decided to try it out. It starts installing, and asks for the second dvd for the drivers. NP, I put it in and an error comes up "cannot find c:\....\Drivers"
So I reoved the dvd, cleaned it, looked it over, and popped it back in. same thing. Argg.
So I create a new DVD for the drivers, pop it in, same thing..
So I decided to try putting in a different cd drive to read from -- same thing. So, I re created the XP DVD and re-ran it -- same thing. So, I tried the same thing on another system to be rebuilt.
However, this time I noticed (should have noticed long before now) that instead of asking for the drivers after it installs, it is asking for the driver almost immediately.
Yes, a bad download. 5+ hours wasted downloading -- 1.6 hours wasted burning disks, and an hour wasted fiddling with the error. Hmmm -- just love wasting time for no benefit...

This discussion is closed to new replies.