Discussion Locked

Can't see added drives on a Dell

0 helpful
19 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I have this Dell Optiplex GX 240 running Windows 2000 Pro that can't see added ide drives in windows explorer. I tried adding a Seagate backup and an Iomega Zip 100 and when I go to view the drives, in Explorer or My Computer, the drives don't showup. When I use the add hardware wizzard, it tells me that the drives are working fine and there are no conflicts. Also when I add a drive to the IDE the CD drive is on, it suddenly dissappears in Windows Explorer. When I remove the added drive, the CD drive comes back. Both drives are jumpered correctly. The added drives are slaves. When the added drives are jumpered as master, Windows does not see them. I cannot find a setting in the BIOS that is not allowing plug and play devices. Both drives work on other machines. Any help would be appreciated.

Thanks,
Pat

19 replies

by sgt_shultz

i wonder if the cables are cable-select type? do you have some 'regular' ide cables you can try? otherwise, the master/slave thing doesn't apply...if they are cable-select type cables, take off all the jumpers on the drives and see if that helps any

by jasonbis

Are you on network that won't allow you to have more than a certain amount of drive letters due to network drives? If so they accomplish that through tweak UI. It may be located in the control panel. If you can't find it do a seach for it. Once in tweak ui find the "my computer" tab and you will see all the drive letters there. If most of them are unchecked then no matter what you add you won't see them. Put a check in those drive letters you want and then reboot. You should see them then.

by odurasler

try going to computer management by right-clicking on my computer. Go to the Disk Management under Storage. Sometimes you will see drives are not given a drive letter. provide a driver letter for those drives.

by jimbo

The only way to get around it to do one at time
I?m assuming your OS drive is NTFS and added drive is fat32 or NTFS if your
Os drive is fat32 than your added drive must be fat32

There is no bios setting as far as master and slave concern bios detect automatically

Leave you os drive intact removed cd rom cable and install one drive into secondary connector
As master, (instead of cd rom) go to bios to see drive is there if so than goto disk manager see you can see the drive right click and check for
Errors. (Than again I?m assuming drive is formatted and ready)
If not remove the drive attach to os drive as slave than do same as above

If that works for the other drive put your cd as the master and another drive as slave with ata 33 cable
Although ata66 and 133 are backward compatible some cd-rom do not know that.

Change place of hdd and cdrom see what kind result you get (change master and slave position)
If you have zip 100, some of zip 100 do not require jumper as slave and in bios must be set
To removal atapi instead of zip drive.

Before powering up the system goto bios and check added drive listed correctly base on your
Jumper setting if not windows will not see it.

Jim

by nhlgreg

Adding Disks

When you install new disks in a computer running Windows 2000, they are added as basic storage.

Adding New Disks

To add a new disk, install or attach the new physical disk (or disks) and then click Rescan Disks on the Action menu of the Disk Management snap-in. You must use Rescan Disks every time that you remove or add disks to a computer. It should not be necessary to restart the computer when you add a new disk to your computer. However, you might need to restart the computer if Disk Management does not detect the new disk after you run Rescan Disks.

Adding a Disk That You Removed from Another Computer

The process of removing a disk from one computer and installing it into another computer is different from simply adding a new disk. After you remove the disk from the original computer and install it into the new computer, use Disk Management to add the disk. To do this, right-click the added disk and then click Import Foreign Disk. A wizard provides on-screen instructions.

by raymond.logan

Enter the bios - even though the drive is not listed, go into the option for the primary channel and select "auto detect"? This should make the system check for the secondary drive.

by obersturnbanfuhrer

If you try to add a harddisk into a Dell PC with Intel motherboard on the secondary IDE channel, you don't have to set master/slave, set as cable select (CS). Also, as usual, set the bios for HDD detection as AUTO.

When the drives are detected, you can change the path (or rearrange) in Computer Management Console.

Right click My Computer => Manage
Under Computer Management tree look for Storage subtree, ang click Disk Management.
Right click the desire HDD / partition (on right panel) you wish to manage.

by patrick horn

The Drives that I am adding are both removable storage drives. The Seagate is a tape drive and the Iomega is a disk drive. The BIOS will see the added drive on IDE 2 but in Windows, I cannot see the master or slave drives on that IDE. As soon as I remove the slave drive, the master shows back up (the CD Rom Drive). When I take away the CD Rom Drive and just attach the Seagate or the Iomega drives, they are detected by the machine's BIOS but not by Windows. Under disk management the drives show up and Windows tells me that there are no problems with these drives but I cannot see the drive in Windows Explorer, or My Computer.

by cd2

Removable storage devices do not show up with regular drive letters. They show up under removable storage - physical location (incomputer management) from there you can select whichever drive you'd like to place media into. Are these drives for backup purposes? If yes your backup software will recognize them.

This discussion is closed to new replies.