16 replies
Have you tried the procedures from the following URL ?
http://www.cisco.com/univercd/cc/td/doc/cisintwk/itg_v1/tr1924.htm#31527
Stephen
by jcho
Or try this URL:
http://www.cisco.com/warp/public/779/smbiz/service/knowledge/general/recovery2.htm
Hope that helps,
by jcho
by milstar
by jcho
by dlafrombois
I tried the links listed above and could not get the document they are talking about. I found the reference, which I confirmed.
http://www.cisco.com/univercd/cc/td/doc/product/access/acs_fix/827/827swcfg/trble.htm#xtocid360011
This works because I have had to do this atleast once.
by dlafrombois
by jcho
by lanwanman352
Cisco 2500 Series Router Password Recovery Procedure
http://www.cisco.com/warp/public/474/pswdrec_2500.html
Attach PC with hyper-terminal to router console port
Settings:
9600 baud
No parity
8 data bits
1 stop bit
No flow control
Turn router off and then back on
Press Break on terminal keyboard w/in 60 sec. of power-up to put router in ROMMON
Type o at the > prompt
Record the value of the config register (usually 0x2102, or 0x102)
Example:
>o
Configuration register = 0x2102 at last boot
Bit# Configuration register option settings:
15 Diagnostic mode disabled
...
Type o/r 0x2142 at the > prompt
Type i at the > prompt
Type no after each setup question
Type enable at the Router> prompt. You'll see the Router# prompt
Type config mem or copy start running - DO NOT type config term
Type wr term or show running
The show running and wr term commands show the configuration of the router
Type config term and make the changes
The prompt is now hostname(config)#
Type enable secret
Issue the no shutdown command on every interface that is used. If you issue a show ip interface brief command, every interface that you want to use should be "up up"
Type config-register 0x2102, or the value you recorded in step 2
Press Ctrl-z to leave the configuration mode
The prompt is now hostname#
Type write mem or copy running startup to commit the changes
by jcho
by gjohnson
rjtaylor has given you the book answer, and it is correct, one gotcha to look out for:
Where the book says:
"Attach PC with hyper-terminal to router console port
Settings:
9600 baud
No parity
8 data bits
1 stop bit
No flow control
You sometimes have to adjust these settings to get your router to accept keyboard input from your computer that is attached to the console port. This is particularly true for Laptops and some KVM's. I had to change it to 2400,8,none,2,Noflowcontrol for my new 7140 cisco router before I could get any keyboard input to be accepted. This took hours on the phone with CISCO TAC, but now that I know this trick, I don't freak when I can't initially talk to a router, Ijust have to spend hours getting the right combo on hyperterm.
Good luck
Geo
by jcho
by vbarnard
I'm not sure if this still applies, or if you have already got the answer, but here goes
1. power off
2. wait 10 secs
3. power on
4. press CTRL-BRK within 10 secs
5. prompt s/b >
6. o/r (RETURN)
7. i (RETURN)
8. choices - configure from scratch
This allows you to create your own config
OR
type "no" (RETURN)
9. prompt s/b hostname (boot) >
10. type "enable" (RETURN)
11. get "hostname #"
12. type "show config"
last time I tried this was a year ago, and it showed all passwords
by jcho
by jcho
This discussion is closed to new replies.
Trending Security posts
Sort by Trending