Discussion Locked

compaq presario 4800-pII-266-96mb sdram

0 helpful
13 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

on a customers pc system hangs at boot up after depassing the pass. we see only compag-sign.
i tested drive with antivirus-cd(2002). no virus.
can i execute the following commands ny using a standard boot-disk?
fdisk /mbr
sys c:

if i can enter with safe mode, what can i do?

maybe sdram (64+ 32, pc-100) should be replace. i will run test-program. do you know an alternative to ctram51? sorry i have the link somewhere, it was posted here.
maybe i will clean the contacts before executing the test.

i do not know yet how to enter the bios. i do not see anything at start. i will check compaq.

13 replies

by wim

With a compaq pc = F1/F2/F7 or F10 enters the bios, depending on your system.

Try booting with a bootdisk, to make sure all hardware is checked and the boot process proceeds.

For the RAM, try booting with only the 64 or 32

If you managed toboot with a floppy you could fdisk /mbr, but I don't believe it's needed.
You could than try sys a: c:, if you use DOS/Win9x

hope this helps

by europanorama

the problem: cusotmer does not have a bootdisk made by the system. i will try with standard bootdisk.

by cg it

fdisk/mbr redoes the master boot record. Unless you are going to redo the entire drive re delete all partitions, recreate primary partition and make active, format and reinstall the operating system, I wouldn't use it.

If you enter "safe mode" you can install individually all windows "components" to determine which one "hangs" the system. IF you can boot to an "A" prompt, atleast your machine is passing the POST tests. That would indicate a problem with the BIOS handing off control to the operating system. Try the hard drive in another system. See if that system experiences the same problem.

by cg it

I assume that the O/S is Windows 9X [ME]. Please provide what operating system is on the machine.

by cg it

this sounds more like Windows having a hard time loading a driver. Again, if you can boot to safe mode, try loading Windows componets individually.

by europanorama

that was a new tip. loading drivers in safe mode. its win98se, sorry.
i did not have yet possibility checking meachine again.
i can boot to a. i use a nsworks-boot-cd. it uses virtual drive a. is this the same? i did not yet boot to a directly. i was very surprised when pc bootet the cd. since at that time i could not enter the cmos and check the bootsequence.
maybe the cd-rom is at third position ()a, c, cdrom) and system cannot boot c then uses cd, right?

by rcom

A recent problem I had and thought it was the hard drive was the cdrom that was going out. You can try disconnecting the cdrom if it's attached to the hard drive. Depending on the hard drive type you may need to change the jumper setting if there's no slave attached. Compaq uses cable select on a lot of the cdroms.

If you can get to the boot menu by pressing F8 select step by step conformation and choose yes to starting items one by one til the system hangs. Then try it by skipping that driver.

Try pressing caps or numlock to see if the lights on the keyboard turn off and on if they are the system isn't totally locked and something is going on in the backround.

Depending on where it stops responding, Anti-Virus software that may be what's stopping the boot process. If it scans from the Autoexec.bat file edit the file and put "rem" in front of the command lines that start the scan.

Disable the video driver will be like safe mode but with the other drivers loaded.

Boot to DOS change to the windows folder "cd windows". Edit the system.ini file from a DOS prompt.

Find and change the line that says

display.drv=pnpdrvr.drv to display.drv=vga.drv.

This will boot the system into 16 colors and will eliminate the possibility of video driver problems.

Here is a link to the parts reference manual for this PC. It has mother board diagram parts listing and the jumper settings for clearing the BIOS. I also noted that there is a jumper to allow the BIOS to be accessed. Also from this same place oyu should be able ot find other info on this and other HP/Compaq systems.

ftp://ftp.compaq.com/pub/supportinformation/consumerdocs/Consumer_QRG/presario4800.pdf

by europanorama

sorry i cannot give any points since my (stup..) customer does not want listening to me(buying new cheap sdram 2x128 mb) and found another cheaper?/free serviceman...but tried installing winxp on pentium II-266-96 mb sdram.....!so i cannot test yoursuggestions.

This discussion is closed to new replies.