Question Locked

Drink spilled on Dell d820 keyboard

0 helpful
10 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
My kid spilled drink on the keyboard. Now the laptop would not turn on. Where to I start? All suggestions welcome.

10 replies

by maniacman

Was is just water or a sugary softdrink? A water spill is much easier to deal with than a sugary soda pop spill because it will make a gunky mess inside the keyboard and will create all sorts of mechanical issues with the keys, not to mention possibly corroding the electronic circuitry inside the unit. Your best bet is to take it to a professional repair shop where they repair laptops and hope it's still fixable. All the luck to you.

by mjd420nova

If you have the skills, complete dis-assembly is required. If you don't have the skills, you'll need to take it to a service center for cleaning. If you have the skills, dis-assembly of the entire unit is needed, and all circuit boards will need to be cleaned, first with a multi-purpose cleaner like Windex multi-purpose cleaner and a soft bristle brush. I use a cut down paint brush. Then clean with a clean brush and clear water. Finally it needs to be washed with an electronic cleaner that leaves no residue. Re-assemble and try the unit again. I was able to resurrect my daughters Dell Insirion 6000 after she spilled a cup of coffee in it. Is is a messy job and care needs to be taken to throughly clean everything and rinsing is important. Non residue cleaners are available at Radio Shack, and NON residue is important as most cleaners will leave an oily film and this will damge the unit if it hasn't beeen destroyed already. Good Luck

by suckstone

Thanks. Am comfortable with dissambly. Will give it a shot.

by oh smeg

Mohawk Safety Solvent to clean the Circuit Boards and keyboard. You can submerge anything in this cleaner and not have a problem it also will not catch fire as easily as most other Solvents and removes a buildup of [b]Gunk[/b] easily.

This is safe with Plastics & Electronic Circuity though a bit rough on the hands as it will strip out any Oil very quickly.

I've used this to clean up M'Boards for years and never had a problem with it.

However when you strip the unit down look carefully for any signs of corrosion. Especially round Resistors, Diodes and the like and also some IC's can corrode where the legs meet the body of the IC destroying the IC's affected. If there is only light corrosion around solder joints a clean with Mohawk will resurrect the Board but if the corrosion is at the actual component the unit will fail very soon if it works at all.

Depending on what was spilt on the unit the Keyboard may need replacing but if you can get to it quickly things are better and the likelihood of a working unit after the clean is far greater.

Good Luck in your attempt to repair this unit

Col

by suckstone

Have the unit dis-assembled. Just can't seem to find the recommended solvent. Even tried searching on Google without success. Am in the Palm Beach, Florida area.

Any suggestion?

by oh smeg

It may not be available in your area. But I'll look up the agents here for it and post back to you as a possible source for this product.

Just one thing though the smallest amount that I can by is 20 Lites or 5 Imperial Gallons.

In the mean time it wouldn't hurt to soak in Metho just be careful of [b]Fire.[/b]

You shouldn't be leaving the internals around for any time.

Just do not place any plastic case parts into the Metho as they could be affected.

I've just done a Goggle Search and the results are available here

http://tinyurl.com/3bdpxf

Zep Elect appearers to be a suitable alternative

Zep Elec II? - Electrical Contact Cleaner. Removes dirt and oil from precision equipment with no residue.

You can find it listed here

http://tinyurl.com/338pfd

Col

by suckstone

Did find Zep on Google, but wasn't sure that it is a good substitute.

Again, thanks for your assistance.

ps Would be useful to do any resistance readings before apply power? After the cleaning process, of course.

by maniacman

I'm sure I saw something like this sold there. Don't recall the name, but I know they carry this solution. Also, you may want to try Goop Off from your local Home Depot, Lowes, etc, as that too will get rid of gunk. Just be careful of exposing plastic to it, as it will melt it like butter if you're not careful.

by suckstone

Update.
Seems as though the motherboard is dead.
Disassembled and cleaned everything.
Plugged in to power and Power Adapter went into shutdown. Guess excess current.
Removed all items connected to the motherboard including the CPU and it still shuts down the Power Adapter. I guess it must have been plugged in after the spill.

Thanks for your advice and assistance.

This discussion is closed to new replies.