Discussion Locked

Dual-boot problem

0 helpful
21 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
I dual-boot win 98 and nt. I converted nt to ntfs (c:) and now I can only boot to nt. Win 98 is on D:, and it actually shows up on the boot menu, but will not boot if selected. I suspect the file for the boot.ini is now in ntfs format and that is why w98 wont boot. Any suggestions?

21 replies

by quahsays

for such dual-boot to work, your first partition must be Win98, i.e. C: must be Win98; then when installing NT, put it in D:.
the boot.ini basically captures what you had. remember that installing NT first will not achieve dual-boot.
for now, put your D: as C: and vice versa, if this still doesn't work, I can only think of re-do all installation.

by avachon

Hi, okay, for a dual-boot between 98 and nt4.0 you must be using the file system Fat16 for C:\ (not only will 98 not read ntfs, nt will not read fat32 which can be read by 98). Although you have the option of reinstalling because you cannot convert ntfs back to fat, you do have another option:
You could use the utility partition magic by powerquest (I'm pretty sure it will allow you to do this conversion; check documentation on website: http:www.powerquest.com). Partition magic is available atmost large computer stores such as compusa, etc. and on the web (e.g., outpost.com, egghead.com - may be cheaper on the web). A future option - get a removeable drive carriage and put nt on one drive and 98 on the other. You then can switch out harddrives and use your os' without worry. One of these can be had for around $30.00 - look at www.directron.com (under hard drives- they have both scsi and EIDE). Hope this helps you.

by avachon

Hi, actually the first respondent said that you had to load 98 first and then nt on a diffferent drive or partition. Well, no, you don't have to do that. The issue is that you have to have fat16 as your file system for a dual boot (and this is because fat16 can be read by both OS'.). In your situation 98 can not see ntfs. If you had installed nt first and then 98, you'd have to use nt's ERD to inspect the boot sector because 98 would overwrite it (but it's a simple repair). Last I know that sysinternals makes a disk that allows dos to read ntfs; I don't what they may have for 98 and ntfs - site is www.sysinternals.com (may be expensive though).

by joshg

You can leave it the way it is but whenever you want to run Win98 you have to set the active partition to the Part with Win98. Then set back to boot NT. Pain in the rear but it works.

by avadhani

The second answer is the most perfect answer to your problem.The dual boot is to be planned before. It is normally done like this.

partition your disk a small portion as FAT16/fat32 ( fat 16 accommadets win3.11 FAT 32 win95,98) the rest of partion can be used for NTFS. You can specify during Nt installation. the boot file will be in FAT partition for both OS.The actual NT files reside on NTFS providing security.

Than the secon guy for his good sujjestion

by jclaverie

At start, Win98 refers himself on D:, but Win98 can't read NTFS. When you convert Win98 have just one partition in C: (because NTFS don't exist for him, he can't boot.
Use tools like partition magic and back NT on FAT.
If you want partition on NTFS and dual-boot with Win9x, take the last partition for NTFS.
You can also buy tools for Win9x who see NTFS, but I never try to test at boot .

by allan

The guy with post about making the the win9x partition Active is correct. Use fdisk to make the partition active. Then install Boot Magic (Part of Partition Magic) or System Commander to give you the boot options menu.

by zlatin zlatev

I think that the problem is that:
After you've converted your first partition to NTFS it is no longer identified from Win98 as a first partition (C:). When you've installed Win98 you've installed it on partition D:, which for now is (for Win98) partition C:
Besides Win98 have created some files on your WinNT partition during the installation process and it cannot read them during the boot-up process (for more info see:
http://www.sysinternals.com/ntfs98.htm
read carefully the text in red)
Suggestion:
You may try to boot from a Win98 boot-up disk
then "Sys A: C:" (C: will be your Win98 partition)
I think that this may cause WinNT stop booting, so you'll need WinNT ERD
If this does not help try to reinstall Win98
(sorry, but the life is hard :)
Regards,
The BIG RED FOX

by ramy naguib

Use partition magic to reconvert back your C:\ drive to FAT 16.
The problem is simply that win9X dose not support NTFS .
Regards
Ramy

This discussion is closed to new replies.