Discussion Locked

Exchange can Recv Email but not Send

0 helpful
7 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I have one Exchange Server 5.5 and have configured the IMS and checked the SMTP prt 25 to ensure it can recieve email via telnet. The problem I am having is that every time I send email out I immediately get NDR report. I have searched the KB articles at Microsoft and performed their fixes with no solution. My regions DNS server does not allow for _ (i.e. EAT_JOES) and my server name just happens to be EAT_JOES format. I would not think that to be a problem since I can recieve email. I have configured the host name to coincide with the DNS server name. If anyone can help it would be mucho appreciated.
NDR report is as follows:
Your message did not reach some or all of the intended recipients.

Subject: This is a test
Sent: 11/16/00 7:21 AM

The following recipient(s) could not be reached:

'meto8@hotmail.com' on 11/16/00 7:22 AM
The recipient name is not recognized
The MTS-ID of the original message is: c=US;a= ;p=HRE;l=HRE_H28MCF-001116122045Z-2
MSEXCH:MSExchangeMTA:HRE_H28MCF:HRE_H28MCF

Thanks
Rick

7 replies

by tony.colgrove

This seems like it could be a DNS issue. The DNS server your Exchange Server is using might not be connecting to the internet properly. Try this:
Run NSLOOKUP from the command line.
Type the following commands:
set type=MX
hotmail.com

You should see the following result:
hotmail.com MX preference = 10, mail exchanger = mail.hotmail.com
hotmail.com MX preference = 10, mail exchanger = mc2.law5.hotmail.com
hotmail.com MX preference = 10, mail exchanger = mc4.law5.hotmail.com
hotmail.com MX preference = 10, mail exchanger = mc5.law5.hotmail.com
hotmail.com MX preference = 10, mail exchanger = mc6.law5.hotmail.com
hotmail.com MX preference = 10, mail exchanger = mc7.law5.hotmail.com

mail.hotmail.com internet address = 216.33.151.135

If it cann't properly find the domain, you would see this:
**** can't find hotmail.com: Non-existent domain

If you get the second result the DNS server is not configured correctly. You could try a different DNS server (one from your ISP).

Hope this points you in the right direction.

by cgconsult

Hi Rick,

we had the same problem here; reason for that is that we deleted the x400 address.
After several day of resaerch we discovered the problem.
Simply make a new x400 address in exchange per user and up u go.
Also check if the Microsoft SMTP Service is installed on your server, it should be DISABLED. If you are using the Exchange Internet Mail Connector, make sure that service is also running and properly configured.
On the client site go to Tools | Services in Outlook, and select the Delivery tab. Make sure your Microsoft Exchange Transports are in the correct order. SMTP is the protocol to use to send mail. Check to see if it is disabled. Hope it helped
Christian

by cgconsult

Hi Rick,

we had the same problem here; reason for that is that we deleted the x400 address.
After several day of resaerch we discovered the problem.
Simply make a new x400 address in exchange per user and up u go.
Also check if the Microsoft SMTP Service is installed on your server, it should be DISABLED. If you are using the Exchange Internet Mail Connector, make sure that service is also running and properly configured.
On the client site go to Tools | Services in Outlook, and select the Delivery tab. Make sure your Microsoft Exchange Transports are in the correct order. SMTP is the protocol to use to send mail. Check to see if it is disabled. Hope it helped
Christian

This discussion is closed to new replies.