Discussion Locked

Grounding and high voltage don't mix

0 helpful
6 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Just the opposite is true...you should NOT be grounded when working with high voltage. Grounding yourself gives the current a path to flow through.
The device and you should not be grounded.

6 replies

by robo_dev

Then you should not be working with high voltage.

There are a whole host of 'it depends' issues, and any of these issues could result in death or the loss of limbs and/or fingers.

In most cases, any device should be grounded, so a short-to-chassis goes to ground, not some alternate path (e.g. through you).

Most IT equipment is grounded to reduce the risk of ESD damage, and is not high voltage.

Now obviously if you're servicing high-voltage power transmission lines with a helicopter, or you're a furry squirrel running on that same high-tension wire, then your lifespan will be greatly reduced by the introduction of a grounded conductor.

by mjd420nova

I have worked with high voltages all my working life and can tell you that if high voltage elements aren't grounded when you're working on them you will get fried. In no case will I work on any parts of high voltage equipment unless it is grounded. I normally carry what's called a Tic-Tracer in my front pocket to detect the presence of any voltage above 50 volts AC. If it goes off while I'm working, I will remove myself quickly and determine where the voltage is coming from. I have received a 12,000 volt shock and can attest to the fact that if it have been properly grounded I wouldn't have been shocked. The situation occured because of an outdated and incomplete one line diagram of the voltage supply system I was working on and another worker closed in a circuit breaker that had not be locked out and grounded. However, I was wearing flame-proof coveralls, hardhat and rubber soled boots that kept me from being grounded myself or I would have gone up in flames. Twelve kilovolts is very dangerous stuff and can reach out a long distance to find a ground. Having been isolated from ground prevented a current path from being established that would have toasted me in seconds. Proper grounding will save your life.

by jaqui

I only had 250 volts hit me.

yes, complete circuit through my body, up one hand, across and out the other hand.

fortunately, it was only about 100 mA, so it wasn't enough to hurt anyone in good health.
but even at that, it is a time to step away and make sure the grounding is fixed before continuing.

by mjd420nova

Needless to say, that was the last time I messed with high voltage. Another friend of mine who was on the same job went to work for another company and took a 12KV shock too, but he was grounded and it really layed him open. That high a voltage tends to travel on the surface of the skin and sliced his chest open like someone had used a fillet knife on him. I've gotten nailed by the high voltage capacitor known as a doorknob capacitor in the high voltage section of a 25 inch TV. No current but a jolt big enough to make me drop the set and busted the CRT. The most dangerous shock to me is a 400 cycle one, seems the heart tries to sync to it and blows up in your chest. Not normally found in anything but shipboard and aircraft equipment.

by jaqui

Any shock when working on any equipment requires investigating to find the source.

I just get irritated with people saying household current isn't dangerous. [ not that you did say that ]
it isn't really the voltage that is the danger, it's the total current, and the health of the person it's traveling through.
if I'm working with something using pico amps, I'm not going to worry unless it's in the mega volt range.

400 cycle equipment is actually an area that is growing for IT though.
more and more ships and aircraft are getting more and more electronics in them. The newest ships are almost completely computer controlled, which is shrinking the crew size and making them even more profitable.
Airbus has their aircraft controls all computerized, talk about an IT goldmine ;)

by norman9

I service computers, and the manufacturer of one line, in their service training, absolutely teaches, and fails you if you get it wrong in their tests, that when working on a CRT-containig device, whether a stand-alone monitor or in an all-in-one computer, you must DISCONNECT all grounds until after the CRT has been discharged to the chassis. That means no wrist strap, no table-mat grounding, etc. It's only after establishing a continuing ground from the CRT anode to the chassis that it is safe to ground yourself and the table.

This discussion is closed to new replies.