Question Locked

HELP! My PC won't Boot after I installed RAM

0 helpful
17 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Hey,

I have an HP with 256 stick of RAM. I checked what RAM I need online. I bot 2 sticks 512 each. I installed them and the computer was working fine. About 30 minutes later the computer just shut down and rebooted. Chkdsk ran and then I get to a page asking to boot from safemode, last known config etc. No matter what I pick I get a split second blue screen saying to protect your PC its shutting down etc..And it reboots. I can't get into Windows. Same thing keeps happening. When I put in the old RAM it doesn't even Work!!!
What the hell did I do wrong?

PLease help,

N

17 replies

by Former member

If so then they will have to go in pairs. So if you have 3 chips on board, take one out.
Now you will have to take off the CMOS battery (make sure you are grounded at all times when you do this, I:E touch the metal casing while it is off), When the battery is out, wait 15 seconds and then replace the battery, making sure you are grounded. Once done restart your computer, you will have to go into the bios first by pressing the key (depending on your set up) F1, F2, DEL, F10.
When in the bios see if the memory is ok, the reading will be in mb's. If it shows ok then go to "save and exit", this will save your selections (if you did any) and re-boot your computer. Now your computer will boot normally.

Please post back if you have any more problems or questions.
If this information is useful, please mark as helpful. Thanks.

by dexter

There are two slots. i put one of 512 each. I took off the battery and reput it. I restarted and went into the Bios. It is seeing the RAm perfectly. it says 2 512 RAm in there. Still no luck. Anything I could do?

N

by Former member

Go to the "boot" section of the bios and make sure that your hdd is placed second in the boot list. The FIRST boot device should be your cd/dvd drive.
Now try and see if you can boot up normally.

Please post back if you have any more problems or questions.
If this information is useful, please mark as helpful. Thanks.

by mjd420nova

Quite often, empty memory slots get filled with dust and when the new stuff gets installed, it doesn't make a good connection. Remove all the memory and use a stiff bristle brush to clean the slot. Also be sure the little plastic clips that hold the memory in place are in good shape. Often during install, the clips get broken or bent and don't hold the memory card into place properly. Depending on the MOBO mfgr. you can purchase new ones and replace the broken ones. Usually they have small expandable clips that fit into holes in the MOBO on either end of the connector. Other times they can't be replaced or are integrated into the memory card connector or not available and then you've got a problem.

by oh smeg

And make sure that all of it was being seen by the computer and then Save the Changes when you exited?

By your description you didn't and as a result the hardware was attempting to run with the incorrect Memory Map which eventually caused a Critical Error and the system BSOD out. On the reboot because of the error it attempted to repair the Faulty Partition and with the incorrect Memory Map this caused the Partition Information on the HDD to become damaged.

Start off by entering BIOS and checking that the correct RAM is being seen and save the changes on exit as the change is the new Memory Load and then try running Chkdsk again.

If this doesn't work and you have a M$ Branded Install Disc as apposed to a System Makers Recovery Disc you can attempt a Repair Install by following the directions here

http://support.microsoft.com/kb/315341

Col

by dexter

When I go into the BIOS the RAm is being displayed correctly. I don't know how to get into CHKDSK since I can't get into the PC at all....I dont think I have a recovery disk.

by Former member

If so then try this:

Repair Install
If XP is corrupted to the point where none of the previous solutions get it to boot,
you can do a Repair Install that might work as well as keep the current settings.
Make sure you have your valid WindowsXP key.
The whole process takes about half an hour depending on your computer
If you are being prompted for the administrator's password, you need to choose the 2nd repair option, not the first.
1.Insert and boot from your WindowsXP CD
2.At the second R=Repair option, press the R key
3.This will start the repair
4.Press F8 for I Agree at the Licensing Agreement
5.Press R when the directory where WindowsXP is installed is shown. Typically this is C:\WINDOWS
6.It will then check the C: drive and start copying files
7.It will automatically reboot when needed. Keep the CD in the drive.
8.You will then see the graphic part of the repair that is like during a normal install of XP (Collecting Information, Dynamic Update, Preparing Installation, Installing Windows, Finalizing Installation)
9.When prompted, click on the Next button
10.When prompted, enter your XP key
11.Normally you will want to keep the same Workgroup or Domain name
12.The computer will reboot
13.Then you will have the same screens as a normal XP Install
14.Activate if you want (usually a good idea)
15.Register if you want (but not necessary)
16.Finish
17.At this point you should be able to log in with any existing accounts.

Please post back if you have any more problems or questions.
If this information is useful, please mark as helpful. Thanks.

by dexter

Im gonna try again soon but I remember the boot sequence was hard drive first. I think I changed it to the CD or DVD or something to try and get into the computer at least thru a CD or something...
It didnt work though. The light on the DVD drive came on and then it just went right back to the same screen...
This is so frustrating!!!

by Former member

Please read this, this is the setting that you need, even if you need to re-install any operating system.

In the BIOS, set the booting devices as listed:

1). First boot device: CD/DVD.
2). Second boot device: Floppy.
3). Third boot device: Master Hdd (if IDE type).

Please post back if you have any more problems or questions.
If this information is useful, please mark as helpful. Thanks.

by dexter

I tried some combos of orders. Im pretty sure I tried that one out. Why does it have to be in that order? WOuld it not work otherwise?
The PC is at my mums so I read whats on here and when I get a reply I go try it there..
If thats not it what could it be?

by oh smeg

Or the system will not boot off the Optical Drive. Ideally you should boot off a Floppy First then a Optical Drive and finally a HDD for Domestic Computers. If there is no Floppy it can be deleted from the list but the Optical Drive has to be listed before the HDD or it will be impossible to boot off a Optical Disc with a Formatted HDD.

Even with a Blank Partition on the HDD you will be unable to boot off the Optical Drive all you will get is an error message with a message about No OS Present insert Boot Disc and Press Enter to Continue.

If the Optical Drive is listed after the HDD that is all you will ever see and get no further.

Col

by dexter

Thats what suck. I have no XP disks..I cant repair. No other way?

by dexter

So no XP disk. Everything in the boot sequence seems right. I put the CD first. I tried to make a boot CD online with my other PC. I out it in. nothing. It goes right back to the main message. i dont know what to do...This seems very bad,

by Former member

You will need some floppies though, so get some floppies and then you can transfer the info over to your computer and make it reboot or do a repair.
http://www.allbootdisks.com/download/xppro.html

Please post back if you have any more problems or questions.
If this information is useful, please mark as helpful. Thanks.

by tukotk421_99

were the NEW sticks the same voltage as the old one was? maybe the voltage is too low? Try taken them both out,clearing CMOS (take out battery) then reboot in the DEFAULT mode ( in the bios screen)

by dexter

Problem since I took out the new RAM and took out the battery, reput the old RAm and reput the battery and still nothing.

The exact message I get before the question screen of booting is

"A problem has been detected and windows has been shut down to prevent damage to your computer.
If this is the first time you've seen this stop error screen then restart your computer. If this screenappears again, follow these steps:

Disable or uninstall any anti-virus, disk defragmentation or backup utilities. Check your hard drive configuration and check for any updated drivers. Run CHKDSK /F to check for hard drive corruption, and then restart your computer.
Technical info:
***Stop 000 etc.

I can't get into the pC to try and do anything though,

This discussion is closed to new replies.