Discussion Locked

How do you network 2 pc's?

0 helpful
18 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
Hi, I am trying to network 2 pc's. Can I do it with a direct cable connection? Or do I need networking equipment?

18 replies

by spydergst1

You can do it. Its called peer to peer networking. i'm not sure if it will work with ethernet cables. you may have to use serial cables.

by gbainbridge

Yes you can do it via a direct cable connection, using one of 3 ways:

1. Using MS Windows and direct cable connection. You'll need to set up one computer as the host, and the other as the client, and you'll need a cable (I'm not sure exactly what kind of cable this requires) that will connect between the parallel or serial ports on the pcs.

2. Using network cards. If you have a NIC installed in each PC, you can network them directly depending on which network medium you use (10b2, 10bT, etc). This can be done without a hub, and is not dependent upon Microsoft's operating systems.

3. Using USB. I honestly can't tell you which MS OSes support it, but USB direct connections are supposed to work with the new OSes like Win 2k and ME. I don't know about Win 9x. You'll simply need a USB cable connected between the 2 PCs.

I hope this helps.

by theophotech

You can network them together easily with an ethernet cross-over cable which is just like a standard cables but all the wires get reversed at the other end. Or you can use standard cable with a hub or switch. You can use a serial cable, but it is very slow.

by tim.mehrley

you can do it with a serial connection, however, using two nic's and a crossover cable will give you better "network" performance. you won't need any special network equipment like a hub.

by eyesak

You can buy a null modem cable and hook the pc-s together, using Direct Cable Connection.

You can install Direct Cable Connection via
Start/Settings/Control Panel/(Add/Remove Programs)/Windows setup tab
Choose Communications, then details button.
Click, "Direct Cable Connection", Click OK, you may have to insert your Win 95/or 98 CD in the CD-ROM drive, if you do not have the .cab files on your hard drive.

Check your Network protocols:
Go to Start/Settings/Control Panel/Network

Youwill need the following Network protocols: Client for Microsoft Networks, Dial-Up Adapter, TCP/IP, NetBEUI, File and Printer Sharing for Microsoft Networks, and
optionally IPX/SPX.

Also in the Network control panel click the
"File and printersharing" buton and choose the following:
I want to give others access to my files and
I want to be able to allow others to print to my printer(s)

Here is a good resource for this method.
http://www.kime.net/directcc/directcc95.htm
You can buy a cable from many computer stores.
Here is a link to buy a parallel or USB cable via the Internet, also
has configuration information.

Hope this helps eyesak.

by eyesak

I forgot a link from my other answer.
You can order a parallel or USB cable for
direct cable connection from the following site:
DirectParallel Home page
http://www.lpt.com/

by vc

You can go about this 2 ways:

1. use 2 network cards and a cross over cable and then set up your protocols using TCP-ip or one that you prefer.

2. Use 2 network cards,small hub,2 patch cables. And then setup up your protocols and configure it.

If you do not know how to configure your network then after installing and setting up your network cards right click on your network neighborhood icon and then go to properties and then go to protocols and click add netbuei is the easiest and then share your h/d by first turning on file and print sharing under your properties and then going to windows explorer and right clicking on h/d and click sharing. If you want TCP-IP then what you need to do then is asign it a IP # and subnet you do not need a gateway unless you have a router/proxy server but that is a whole other story. if you need any other help please feel free to email me at harley.roming@killeenisd.org

by vc

why someone would want to connect with a serial connection is beyond me because it is so very very very slow. The cross over cable or with a hub bascially using 802.3 standards is the best way to go with this so that you get speed and stability.

by baziite

You Just need to buy a Parellel/serial Null modem Cable , Connect it to the Parellel/Serial Ports of the two computers and use the Direct Cable Connection Wizard to configure the network . One Computer will become the Host and One will become the guest . To Start the direct cable connection wizard just click Programs / accessories / communications / Direct Cable connection . If the Above shortcut is not present then you have to install it using windows setup from controll panel . You don't needany networking equipment if speed is not the issue .

This discussion is closed to new replies.