Discussion Locked

how to configure two network adaptors

0 helpful
5 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Im having a server with two nic installed
One is used for a dsl cable connection and
the other is used for lan. the server is a
domain controller. when i connected the dsl
connection none of my local area networks are not connecting to the server.

pls suggest

5 replies

by jose_12650

We need more input from you for better analysis of the problem. Your brevity, will make us assume certain parameters which may not be correct.

We me assume though that your static IP for tne NIC on the lan and the NIC that is connected to the DSL are within the same network range, which we could assume also in the range of 192.168.0.0. because you have access to the internet.

by shmaltz

You have to give the NIC that is connected to the LAN an IP address that is local to your LAN. Have the NIC that is connected to the DSl obtain an IP address from you ISP (if you have static configure it with the IP config from you ISP). Then you have to enable IP Forwarding.
To enable IP forwarding in NT you have to do that in the advanced TCP/IP properties. In Win2K you have to enable RRAS in the administrative tools.
After the Server has IP forwarding enabled you have to configure the client and make sure that it has:
1. An IP address that is local to the Servers NIC that is connected to the LAN.
2. The default gateway points to the Server.

The above is the basics for setting it up. Keep in mind that with the information you gave(you didn't say what OS, Whats with DNS, and much more is missing) there isn't a lot more I can write.

by goks_77

The problem is our LAN is not working where we enable the DSL NIC Card. When we disable the DSL connection in the server then the LAN is working.

The OS is 2K Server. Between the nodes V R getting access. From the server to the all the nodes V R getting access. From none of the nodes V R not getting the access to the server. But all the nodes R pinging through normal pinging as well as TNSPING (ORACLE)

1 NIC is using 10.20.121.0 IP Address and 255.255.0.0 is the subnet mask and 127.0.0.1 is the DNS. This setting V R using for the LAN.

The other one is 10.30.1.2 and 255.255.255.0 is the subnet mask and 10.30.1.1 is the Gateway and the DNS 202.9.145.6 and alternative DNS is 202.9.145.7. This setting V R using for DSL.
If wetake DSL Connection's TCP/IP properties -> Advanced Settings TAB "IP Addressing" default gateways option is set to 10.30.1.1 and Metric is set to 1.

by ctmoore1998

This is called Multi-homing your server. The only reason you would be doing this would be to run either firewall software on your server (not recommended), proxy server or the server is the only device getting internet. If you aren't doing any of these things multi-homing isn't recommended or needed, you can just plug the dsl into the hub and use as default gateway. Now if you have DNS on a 2000 server already configured to be the DNS, then lookup multi-homing at microsoft.com/technet there should be a doc to configure the lan and wan NICs and DNS. But basically you have to config 2000 DNS to be the LAN DNS server and then config routing and remote access to RIP the internet thru the 2000 server you then have no default gateway on server lan nic and dsl as default gateway on wan NIC also go to advance deselect dns update option for the WAN NIC. In DNS remove . and then you can configure DNS forwarders use ISP DNS servers for forwarders. If using DHCP then configure to point DNS at server IP if static each workstation will use server ip as DNS. On server CD install tools and run NETDIAG /v >Netdiag.txt then edit result to see that DNS is configured ok. These are the mere basics for multi-homing a 2000 server if your server is NT then its a different procedure. Check MS technet for detailed instructions

by goks_77

The problem is our LAN is not working where we enable the DSL NIC Card. When we disable the DSL connection in the server then the LAN is working.

The OS is 2K Server. Between the nodes V R getting access. From the server to the all the nodes V R getting access. From none of the nodes V R not getting the access to the server. But all the nodes R pinging through normal pinging as well as TNSPING (ORACLE)

1 NIC is using 10.20.121.0 IP Address and 255.255.0.0 is the subnet maskand 127.0.0.1 is the DNS. This setting V R using for the LAN.

The other one is 10.30.1.2 and 255.255.255.0 is the subnet mask and 10.30.1.1 is the Gateway and the DNS 202.9.145.6 and alternative DNS is 202.9.145.7. This setting V R using for DSL.
If we take DSL Connection's TCP/IP properties -> Advanced Settings TAB "IP Addressing" default gateways option is set to 10.30.1.1 and Metric is set to 1.

This discussion is closed to new replies.