Discussion Locked

How to Install SCO UNIX Ver-5

0 helpful
17 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I need to know how to install UNIX
on my computer, I want to learn UNIX but I
don't want to remove Windows from my system.
My system has extra partitions.
I would like the (setup/install) and config-
uration process please.

17 replies

by antonio.trejo

The tittle for your ? reads SCO UNIX but in the question itself you just refer to UNIX, so I'm not sure if you are specifically after SCO or UNIX in general. If you, as stated in your question, want to learn Unix, then I'll asume that you wan Unix in general.
I have recently install Linux in my own machine and the installation process went very smooth. I bought Red Hat's distribution and the graphical interface was nicely explained in the installation guide. The box came with 3 books: Installation guide, Getting Started and The reference. One of the apendixes in the reference talks about partitions and gives a clear idea of what needs to be present or not in your HD for a smooth installation. If you need resize your partitions, you can doso without removing Windows with a utility that cames also as part of the distribution.

With all the books and online reference out there about Linux, I consider this to be a very good way to start your new Unix adventure and possibly way of life.

by zmira

If you really want to learn UNIX you should select Solaris for x86 which cost only few dollars( www.sun.com).
I am pretty sure that you can have both on the same disk, but I have not done it myself being a true SUN guru.
Installing the x86 Solaris give you access to one of the best Unises.

by tmhunt2

From my limited experience with older versions of SCO, Santa Cruz's OS is much like Windows when installed. What I mean by that is when you install SCO, It will blow away ANY other partitions that exist and claim the drive for itself. Again let me state this was for an older version of SCO (3.2v4.2) and I do not claim to be a guru .I seem to recall the same thing when I tried to install Unixware 7 but I gave up on installing the OS pretty quickly. If I were you I would get a copy of Linux.I have tried Red Hat and Mandrake distributions and like them both but I use Mandrake 7.0. I was once in your shoes and I found Linux to be the easiest to install and it plays very well in the sandbox with other OS's. I made a few mistakes along the way but they all helped me to learn. Look at a few other distributions, each has slightly different installs, and decide for your self. Get a book or two a read up before you start. The "Dummies" books are not a bad place to start. That's how I got started. Hope

by bmw

Installing SCO Unix is a fairley simple process. You say that you have extra partitions, if you have a partition that you are certain contains no information that cannot be overwritten then proceed as following:
Change the boot device of your machine to be the cd-rom drive (or if you have a boot disk, boot from that).
Follow the on screen prompts, until you reach the hard disk initialsation section: there you will have the choice of 'use whole disk' or 'interactive fdisk/divvy', select the interactive option, select the partition to use when the procedure takes you into fdisk and continue.
When you reboot your machine, you will be confronted with a 'boot:', if you hit return it will take you into SCO Unix, but if you 'dos' and then return, it will take you to Windows or whatever was on the other partition.
The only tricky aspect of the SCO install is the 'fdisk/divvy' stage, you could lose your Windows partition if you are not certain which is your free partition!

by flodman2

I use SCO 5.05 at work and have installed the Linux version called slackware follow this link and download the Zipslack it relies on similar principles to 505 and i have found it very useful for learning things like sendmail. It runs nicely on my machine and doesnt interrupt with windows. i dont even need a new partition. just unzip it to a folder read the readme and get running linux.
the user groups are friendly and the online documentation is good.
http://www.slackware.com/zipslack/

by ca_rlittle

The answer to how is, don't. SCO is a breed of its own. Don't get me wrong, once you are comfortable with it, it is a great implementation of UNIX.

If you want to learn UNIX then you should try the ever popular Linux or Solaris. Using Linux will teach you how to use many UNIX commands. You can get Solaris X-86 from there web site for the cost of shipping. Once you install this on your machine you will be learning how to use an OS that is widely used in industry. Also, the differences between the X-86 version and the SPARC version are basically at the hardware level. If you learn X-86, you will be able to migrate to SPARC environment with little changes. X-86 is great. I have used it for years.

Be sure to check the Harward Compatibility List (HCL) of any OS before you purchase though. You wouldn't want to start loading it and find that it won't work on that 286 or that brand new 1GHz machine of yours.

by johan

Installing SCO Open Server 5.0.x is not so difficult. You need a registration for it. On the www.sco.com site it is possible to obtain a student license for free. The only thing you should worry about is that for all bootable partitions the startup kernel should be within the 1024 cylinder boundary otherwise the system doesn't start. You can install Unix with the proper installation set on an empty partition that should be at least about 500Mb free. Sco takes over the boot sequence, but after installation at the Unix boot prompt, just type dos to enter your windows partition. If you would like to know exactly how this should be done I can send you some documentation from the SCO digital documentation set about this item. I have done this several times from SCO Xenix up to the newest SCO Open Server 3.2v5.0.6.

This discussion is closed to new replies.