Discussion Locked

How to restore AD in single DC/Domain?

0 helpful
4 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Hi all,

I just lost my single DC in single domain due to hard drives failure. The DC was configured with two mirrored SCSI 36GB drives, and a third 36GB in which the AD log files were located. One hard drive failed last Friday morning and today the second one failed!!

I do not have any other DCs on the network. I have told management many times before about the need that I had for another DC on the network for fault tolerance, but because of financial reasons this cannot be done until the end of November.

I should receive the replacement hard drives hopefully next Monday.

1- How do I restore AD?
2- Is it better to use Raid-5 instead of mirroring? Do I have to create disk volumes with the same drive letters, etc as before?
4- I am using Veritas Backup Exec 8.6. I?ve configured and scheduled a full backup every night of the C: and system state data plus the log files on the third drive.

If someone out there has gone through this process before could you guide me in the right direction or point me to the right resources. I have looked into the MS knowledge base but I have not been able to find a step by step guide on how to recover a single DC, all the articles that I've come across talk about AD recovery when there are multiple DCs. FSMO rules etc. Since I only have one DC, I believe that this DC hold of the roles. Am I correct?

I know that there are too many questions but I am desperate. I am a AD newbie :-(

Thanks in advance.

4 replies

by rabbit_runner

This is not for the faint hearted. The following is a simple outline for what you will need to do.
1. When you get your hard drives into the machine, Load the OS in the same exact environment that you had before. Partitions, drive leters, etc. Same Domain name, same services (IIS, DNS, DHCP, WINS) that you had on the first server. Name the computer the same, same IP, same drivers, etc. Make the new server as close to the original server as you possibly can. NOTE: It will still be a different server from the original, at this point.
2. Install any applications that you had on the server.
3. Load your Backup Exec on the server and make certain that you can do a backup and restore of a few files on another tape.
4. Thoroughly read KB articles from the Microsoft Web site. Here is one dealing with an 'authoritative restore' of AD
http://support.microsoft.com/?kbid=241594
There are many more KB's you can read to give additional info.
5. You must re-start the server in "Directory Services Restore Mode". Now attempt your restore.
6. Please remember, that there are still a thousand things that can go wrong.
If you, or your administration, expect this to be a simple task, or one that will go quickly, do not 'hold your breath'. AD is a 'bear' to do a restore. Murphy's law ususally holds true. If something can go wrong, it probably will. In all likelyhood, your network will be 'down' for a while.

by rabbit_runner

All of the above is information if you attempt to do the restore by yourself. Since you state that you are an AD newbie, it would be best to contract out to a consultant, with experience in AD restore. It will cost the company more, but fewer problem will occur, and the system will be up and running more quickly.
As another point, if you do hire a consultant, have that person give a recommendation (in writting) to the Administration that they MUST have a second domain controller. Your current problems only emphasize that. Even as a minimum, get a used low end system. Then when your domain is back up and running like you want it, use this other system and make it a second DC. It does not have to have any applications, only the OS. Then if the main DC goes down, you will still have a working copy of your AD database. Your network will still be in operation, while you fix your main DC.
Hope this may help.
Michael R.

by casta

Michael,

I was able to bring the DC back even though I only received one drive instead of two. So I partitioned this one drive and assigned the same drive letters and followed your suggestions and MS articles that you kindly sent to me.

The network was down for a day, I honestly thought that it was going to be longer than that, but I worked my butt off for that day and we were up and running later on that evening. It was very nerve wrecking but it was the best lesson in AD recovery that I could ever have.
I have setup another box as a second DC for now. So I can breathe a little easier until we get the new hardware.

Thank you for your help but mostly for your time.

John C

This discussion is closed to new replies.