Question Locked

Installed new RAM, Now I have blank screen on boot up.

0 helpful
11 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Well, as the title says I went and bought a stick of 2gb DDR2 RAM to go along with my already two single 1gb DDR2 RAM in the computer. Unplugged every cord, Installed it with a bit of conflict with my long graphic card and turned on my computer after plugging everything back in to find that neither of my 2 moniters were getting a signal(The computer was able to boot up though).

Next I decided to take out the new RAM and leave the old RAM in and see if it would work and I still had nothing. I checked my graphics card and it still seemed to be in it's slot well enough (Would have completely taken it out but the lock on it was giving me problems)I checked the moniter cables they were fine and I even tried connecting a moniter back to the intergrated graphics chip (came with my computer before I purchaced a new graphics card)to see if I could get a signal and still had nothing. I've switched the RAM sticks around a few times and still haven't got anything... btw I am running on Windows Vista Home 32bit.

Sorry for the long post but I tried to be as descriptive as possible. Anyone have any idea of what I've done/what's happened to my computer? :(

11 replies

by w2ktechman

blew some chips with static.

try 1 chip at a time (unless your motherboard requires banks).
If banks are required, it may just be bad positioning of the chips. Look up the specs for your motherboard and proper RAM placement/installation

by rob miners

removing any addon cards eg: modem, USB, Firewire

Is it beeping if you remove all of the RAM.

< missed a bit >

Is it beeping if you just have one stick of RAM or is it beeping at all.

by tajunk

I've tried single placements of the RAM and I've no results as well as no beeps. I've tried removing all of the sticks of RAM and still had no beeps. I'm guessing this means my motherboard is dead? Little confusing as the motherboards fan is still going as well as the fan on my graphics card which is connected to the motherboard.

I'm guessing we've reached the point where the RAM isn't even the problem anymore but just in case, http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01065712&lc=en&dlc=en&cc=ca&lang=en&product=3445431 . This is my computers spec.

by rob miners

HP and Compaq Desktop PCs - Monitor is Blank after Starting the Computer

http://tinyurl.com/4wceqp

Turn on the computer and press the keyboard key that enters the BIOS Setup screen key when the keyboard light comes on. The key to enter the BIOS should be one of the following:
HP and Compaq desktop computers that came with Windows Vista, press F10.

For HP Pavilions desktop computers that came with Windows XP or previous versions of Windows, press F1.

Compaq Presario desktop computers built after 2002, press F1.

Compaq Presario desktop computers built prior to 2002, press F10.
Wait 5 seconds.
Press the F5 key to restore the default settings of the BIOS.
Press Enter to accept the change and wait five seconds.
Press the F10 and then the Enter key to save the changes and exit from the BIOS.
The monitor should now display the first screens received from the computer (the logo screens).

Keep us informed as to your progress if you require further assistance.

If you think that any of the posts that have been made by all TR Members, have solved or contributed to solving the problem, please Mark them as Helpful so that others may benefit from the outcome. ;)

by thumbsup2

Just how much 'conflict' did you have with the long video card? Did you pry on it? Perhaps you've damaged the card while trying to get it out of the way of the RAM.

Try removing the video card and reseating it properly.

by tajunk

I tried the solution for resetting the BIOS twice and it didn't yield any results unfortunately.

The conflict was more of the tabs that keep the ram in place, the upper ones would have a bit of trouble going back all the way, and I had to sort of shift the end of the card back slightly to insert the RAM. I don't believe the thing is that delicate, but I may try removing the card and try running the moniter off of the integrated video card again. Or just try to reinsert the card... I'll come back with an update on that tommorow morning for me as it's starting to get really late over here, and I'm going to have to bust out the graphics card manual as this lock keeping it in is causing me grief.

Thanks for your help so far everyone.

by older mycroft

[i]"I checked my graphics card and it still [b][u]seemed to be in it's slot well enough[/b][/u] (Would have completely taken it out but the lock on it was giving me problems)"[/i]

"..in it's slot well enough.." doesn't quite cut the mustard with me - 'well enough' for what? Well enough to not fall out, well enough to refuse to come OUT any further?

By the very nature of the fact that you say it put up a fight when you tried to remove it, its continued occupancy of the graphics slot is most likely tenuous to say the least.

Perhaps the ONLY thing holding it into the slot is the retaining clasp - perhaps it no longer makes any contact whatsoever.

I would suggest you gently prise the clasp out of the way, in the way that it should be done, remove the graphics card completely, clean all the gold contacts with a soft pencil eraser, re-insert the card - locking it in place with the recalcitrant clasp - then try re-booting. :)

by kenone

My solution was, Remove video card (carefully),
Install memory (if already installed remove and re-install - trust me),
Reinstall video card (Carefully)
Re-cable, re-power - boot

The memory needs to kind of "snap" into place and it can't when the video card is in the way, it was almost impossible to get the memory seated correctly with the video card installed.

by rob miners

to your onboard Video after you try the above.

< add a bit >

Have you tried connecting to the onboard Video.

by Former member

You will have to install in pairs.
So you have two choices:
1). Leave in your old 1gb memory.
2). Take out your old memory and just have your 2gb memory chip.
It seams you can not have three chips in play.
To make a full 3gb to utilize the slots then you will have to have: 1 x 2gb memory chip (of which you have), and 2 x 512mb memory chips. That way you have the pairs.
Just put in the 2gb chip and clear the cmos through the pins on your motherboard or cmos button depending on your type of motherboard. Once done it should start up, then you need to go into the bios and set it up the way you want it.

Please post back if you have any more problems or questions.
If this information is useful, please mark as helpful. Thanks.

This discussion is closed to new replies.