Discussion Locked

NT4 won;t recognise ADAPTEC SCSI Drives

0 helpful
16 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
I have an NT4 server which I want to rebuild from the ground up without changing hardware. THe machine has only got SCSI hard drives (no IDE) on it. I have what I believe is the SCIS driver diskette so I tell NT install to load the driver and it does,but then says it can't see any hard drives and exits the setup. The SCSI adapters are Adaptec AIC-7895 according to the SCIS Bios boot message. The disk I have says Adaptec 7800 Family drivers and has a file on it called aic78x5.sys which appearsto be the right file. I looked on Adaptec's page - they say anything that bios identifies as aic0-78x5 is OEM drivers for motherboard and they do not support them directly. I have no idea what the motherboard is - the machine is a few years old. Does nay one have any ideas???

16 replies

by k.o.z.

Does this server multiple drives?? If so it is probably set up with RAID 1 or 5. If this is the case you need to install the RAID control drivers for the specific PC model. If the drives are in a RAID configuration, NT will never recognize the drives. Once you download the RAID drivers off the web site you just type S in the NT setup to specify SCSI adapters and it should load the RAID drivers and you'll be all set. Hope that helps!

by gregory w. smith

If you allow NT to autodetect hardware it will often refuse to load the proper drivers afterwards. If you manually (S)pecify all of the appropriate drivers, you should load just fine with the disk you have.

by ronnonf

I have been in a similar situation: We were installing NT onto a machine with an Adaptec Ultra Wide 2 card and NT would not detect it. You need to press the F6 key when NT comes up the first time with the blue screen and detects the settings. This will allow you to put in the drivers that came with the card. That is when you tell the installation that you want it to use the Adaptec drivers for NT that came with the card.

by 93961

Actually the 789x card drivers are not available on the adaptec site. If your motherboard is from Intel you will get the drivers for the SCSI Card from the Intel Site. You will even get other drivers like the vga & network card from them. All these will be available form intel only if the motherboard is all in one including the scsi adapter. Regarding the driver you have the 7800 card driver will not recognize your present card, i.e. 7895, at all. Even when the driver is availble with you and you install the NT by booting directly thru the NT Cdrom the drivers will report that there are no mass storage devices found. The setup in this case has tobe started with booting the NT Setup Boot Floppies and in this select the SCSI drivers at the appropriate moment. Then only the driver recognizes the storage devices. But you will have to first search the proper driver. Normally by seeing at motherboard you can guess who the manuafcturer is. Best Of Luck!!!

by steven_bvsolutions

If you are booting directly to the NT CD and installing from it you can experience this problem. Create the 3 boot disks and boot off of them and then provide the driver you have when requested for additional devices.

by joshg

If you are booting and installing NT from the CD to a SCSI drive NT will not detect the drives. You will need to use the three setup disks then when you are able to install mass storage drives insert your drivers disk. You should be okay after that.

by nace

I have experienced this several times while rebuilding both NT Desktop PC's and NT Servers.

Boot the server from the NT setup CD or NT Setup floppy disk(#1). When the POST is done and the black screen comes on showing the message "Please what while setup detects your hardware...", hit the "F6" key. Then, the blue setup screen will show up. If you are using the setup floppies then you will be asked to insert disk #2 next. Otherwise, the next screen will be for adding mass storage device drivers. There will be a scroll box showing the few driver sets that NT installs by default. Pess the "S" key at this time (for Specifying a different driver) and it should ask you to insert the floppy disk with the drivers on it and press "return". Thiswill install the drivers for the SCSI card from the disk. When setup is done installing the new drivers, you will go back to screen where you can specify more devices if you wish. If you also have a RAID card then install those drivers now using thesame procedure as yo

by mark l

I have a WinNT/SB-Audio prob. Similar. Diff Cards, but bet the non-boot problem applies to your card too. Found a fix in MS-TechNet Knowledge base at: PSS ID Number: Q109798 dated 01-20-1999. Here's (as much txt as fits) in this box.
=====
NOTE: Though this card will support SCSI hard drives, it will not support booting
from a hard drive connected to it.

For more information about these drivers or the card in general, call Creative
Labs Technical Support at (405) 742-6622.

Creative Labs manufactures the Sound Blaster 16 SCSI-2 audio card. This card
works properly as a SCSI adapter under Windows NT using drivers included in
Windows NT. The audio portion of this card works when you use drivers supplied
by Creative Labs.The Sound Blaster 16 SCSI-2 card has an Adaptec AIC 6360 chip on board which
appears in the hardware compatibility list. If the card is in the machine when
you install Windows NT, it will be detected as an Adaptec 151x/152x/AIC
6260/6360 SCSI adapter. When you add th

This discussion is closed to new replies.