Discussion Locked

onboard-sound-cmos-settings unclear

0 helpful
11 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

i have two entries in cmos of a motherboard with onboard-sound. both can be disabled or enabled.

1. onchip sound
2. onchip legacy audio(shows settings if enabled)

what is the difference?

11 replies

by scott.heath

It's support for how older applications access audio. The old Sound Blaster Pro standard. That game from 97 probablt doesn't support EAX or any other cool features. Of course, how many of us still play those games?

by fred07

If you are using the onboard sound, enable both and have your MB driver disk ready or be running 98SE or above. Newer MB's and you will need your MB driver disk.
You will get better sound [stero] and some are 4 speaker setups.
hope this helps.

by europanorama

i have updated everything(bios,winme,etc.). made cmos clear. i will try using default setting. i have now networkcard(cablemodem) installed. tried out everything. no sound at all. maybe i must use newer than 445-via-driver(4 in 1).

by europanorama

i have tried out both, i mean, point 1 and point 1+2 and i have seen the following. keep in mind i have no network which will normally use irq 10.
if only onchip sound is enabled, irq 10 is used
if both are enabled, irq 5 is used plus dma and i/o adresses in bios.
no errors in windows. but i cannot hear sound on earphone. neighter onboard nor on drives. i treid out digital enabled or disabled. i can see the soundmixer. all enabled. i have setup new via 4 in 1 driver from mb-site. plus i used audiodriver from mb-site(its a acerpower 8400), i had troubled setting up that driver. first it told me it the wrong one and showed errors(in system/deveice-manager) then i was lucky: no more errors. its ac 97... wmd. btw: acer was so stupid to use cheap 200w-psu on that s61-no name-board. it produced a lot of troubles to my customer. after a long pause i could use it again. at the end it was dead or half-dead. why are thes big companies so stupid? it is unbelievable. i am using now enermax eg301ax-ve(g).
pIII-500(100mhz). bus ratio was set 3.5, i have change to 5x.
there are two sdram 128mb. one is pc 100, how can i determine whether the second one is pc-133? it is said that mixing is prohibited, elsewhere i received the information mixing can be done with pc-100 on first place. thanks.
btw: i have agp-videocard ati rage 128 pro.

by fred07

WHOA UP,
Just saw the "earphone" mentioned.
That must be enabled in your sound system.
and damned if I can find it.
Remember if you listen to speakers you can not listen by earphones and vice versa.
Also, only certain mediacan be heard by earphones.
I suggest you repost the question with the header, "enabling earphones from cd"
Sorry I can not be of more help.

by fred07

oops,
And yes the pc100 and pc133 may be mixed. The pc100 needs to be in first slot and will control the speed of both at 100.
If there are no beeps on boot then you are okay.
I use Motherboard Monitor to id and give me specifics on theRAM.
Hope this helps.

by europanorama

the earphone/sound-system with the two separate settings in device manager and mediaplayer is a real mess. it doesnt matter what device/earphone or speaker is connected to the soundcard, same for cd-rom-drive. i could err and will test next time. thanksa a lot, also for the mb-monitor-ram-tip. it was just actual.

by europanorama

i could solve one part of the problem by using viaarena-combo-audio-driver. it is a vt82c686a(im am lucky its not 686b-known as southbridge-problem). i still cannot hear trough drive. i tried out digital analog/dma no dma. soundcable/no soundcable.

by europanorama

friends i could finally find the solution:
1. use earphones on one or both of the two drives(dvd/cdrw).

if you use only a standard soundcable you can only use earphones on the drive with soundcable. drive must be set analogue(digital setting disables earphones).
if you like to use earphone on both drives you can use eighter two cables or y-shaped one if only one connector is present. mb-instructions will tell if two connectors can be used.
now to the main problem i had with winme-mediaplayer. it seems that in win2k drive-settings in system(digital/analogue) will have direct affect to cd-player-settings.
but in winme mediaplayer its different!on lower left corner are play-options.under options-devices you will find the drives where you can activate digital/analogue!it was wrongly set to digital independent from windows-device-manager.

final question: both drives are on secondary channel. dvd is master-cdrw is slave. is this ok? or should i set them vice-versa?

This discussion is closed to new replies.