Discussion Locked

Partioning the 13 GB hard drive

0 helpful
27 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
I want to install NT and Windows 98 on 13GB Hard Drive i want Dual Boot the System. I know that if u want to access Hard drive greater then 10 GB u have to install SP 3 on windows Nt 4.0. i have done that but not able to install Windows 98 afterwards please tell me soloution. I am eagerly wating for response

27 replies

by senthilnathan

Hi,

You need a fat-16 partition with minimum 2gb
for windows-98 system files.

Winnt needs higher version of service pack to access more than 8gb. (latest 6a)

Partition the hard disk as follows

1. Fat 16 partion - 2gb
Install dos, WinNT & win98 in the fat16 partition.

2. Winnt partition - 4gb

create fat32 partition in the remaining space

3. Win98 fat32 partition - 7gb

Hope this will help you.

-senthilnathan.

by gthompso42

I thought it was a minimum of SP4 to go over the 8GB barrier. NT will allow you to create a fat16 partition of 4GB by using 64k clusters, but this is definently not recommended with a dual boot. My recommendation would be to put NT and 98 on different partitions. Applications that you want to run under both operating systems will need to be installed under both

by libran_76

be with the trend why don't u install windows nt 2000 in one partition and win98 in the other partition it does not have any hassles of the fat 16/32 file system but if u want to install winnt ver 4.0 and win98 with fat 32 file system then u have togo to this site and download a software at
www.wininternals.com
but if u want u can partition u drive with fat 16 that will create somewhat 6 partition for u hard disk with 2 gb each
chose what ever u like
hope this might help

by moflic

The easy(expensive) way:
www.partitionmagic.com
Buy Partition Magic.
Saves alot of headaches. Does everything you asked for, even resizes partitions, converts them to every format and boots every OS known to mankind, it's as magic as its name sais. Perhaps even cleans your dishes and dust the carpets :)
2.The tough (and cheap) way:
First install 98 in a FAT32 partition and leave empty space for the future NT instalation. Then install NT in the empty space by formatting that space to NTFSor FAT. NT will recognize the 98 instalation and will provide a menu at boot time to boot to win98.
3.The hard (most self-satisfying) way: LILO (search the web for it (LI(nux)LO(ader)), and read the docs, they provide info on how to do that).
4. Search the web for other boot managers (there's a bunch of them)

by rindi1

I suggest the following method:
create a primary fat16 partition which is a about triple your RAM size. This will be your boot partition. with the rest of your disk create an extended partition and divide it into two 2GB (FAT16) logical drives. Nowinstall windows 98 drive D. Once finished, install windows NT to drive E. Now, if you want to be able to read an ntfs file system from win98, download the utility "ntfs for win98" from the site www.winternals.com ($49.--) and install the utility. Ifyou also want to be able to access fat32 from NT, download "fat32 for NT" from the same site ($38.--) and install the tool. Also apply the newest service pack. now you can change drive d to fat32 and drive e to ntfs. If you want to change the size your your partitions you can use powerquests partition magic. Otherwise you can partition the rest of your drive to an ntfs or fat32 drive (f) and use that with both OS.

by rindi1

Sorry, i forgot to tell you what to do with your C (primary) Partition. Place the pagefile there, thats why i told you to make it about three times the size of your RAM. You can also place some driver etc there which you may need to set up your hardware with (NIC Cards etc). You can use the same pagefile for win98 as well, just edit your [386Enh] section of your system.ini file and add the name of the file:

PagingDrive=C:
PagingFile=pagefile.sys

Also be sure to install windows98 BEFORE winNT, that way nt's boot manager will be correctly installed

by leo.valmores

Hi,

I think it's more important also to consider whether or not you are going to share data between NT and 98 applications. If sharing is equally important, DOS FAT16 partition is accessible to both NT & 98 file systems. However you also have to accept the fact that DOS partition is limited to 4GB. For security-sensitive data files, use NTFS since this allows you file-level security. Unfortunately, WIN98's FAT32 file system is not the same as NTFS' file system.
Here's my suggestion:
1. Create a FAT16 4GB partition and install DOS/WIN98.
2.Once WIN98 is installed, install NT and let it intall to a new partition, 4GB (limit for SP4).
3. You can create the remaining 5GB either in WIN98 FAT32 data partition or NTFS FAT32.

by dragon_p17

IF YOU WANT TO DO MULTI BOOTING U GOT FIRST
REPARTION THE HARD DISK TO 6 PARTIONS
CUZ. YOU GOT TO HAVE AT MOST 2GB FOR EACH PARTION THEN INSTALL WINDOWS98 FIRST THEN INSTALL THE WINNT ALSO, THE FAT MUST BE TO 16BIT AFTER THIS U CAN CONVERT THE WINDOWS98 TO FAT 32BIT ALSO, THROUGH INSTALLING WINNT U WILL FIND OPTION THAT GIVES U THE ABLITY TO USE MULTY BOOTING. & IT'S BETTER TO BUT EACH WINDOWS IN SPEARATED PARTION

by laust

I read an article that mentioned that you should always install windows 98 first and then install windows NT.
This way NT recognizes 98 on boot up.
So make a partition for 98 format it and install 98 in it. Then go on to the installation of NT and continue partitioning as required.

by know nothing

just for your info you can get fat32 for NT at C Net downloads for free and most likly NTFS for win98 also.

by eshar

It is very easy to do this. I have a 20Gig and i got it to dual boot with a fat32 partition. First creat a fat16 partion of about 200 Meg. quit fdisk and reboot the machine with a bootable disk run fdisk again and use large disk support. Create a second partion of the amount desired for win98.
exit and reboot the the machine with the bootable disk. format c: and d: leave e: as the rest of the space available for NT. Make sure u install win 98 on d:. Once it is done start installing nt. Create the last partion using NT during your installation process partition the drive according just remember if it is fat in nt cant exeed 4gig so split them into 4 and 4 till there is no more left to do. choose a partion to install it on. Once it is done go into nts disk administrator and create a volume set for the drives u made 4gig and 4gig.

thats is how it is done

by darrenb

If I read the question correctly you installed NT first. In a dual boot situation win98 must be installed first. Then when installing Nt it wil detect the existing OS and ask which partition you want to install it to. It then will modify and add 3 files to the MBR record. Doing this vice versa will simply overwrite the MBR.

This discussion is closed to new replies.