Question Locked

Ports

0 helpful
19 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
I had to crash my desktop computer. Since that time I have re-installed all the software without any problems. The only thing it is giving me any problems with is trying to install any outside equipment. It won't let me install my printer or my scanner. Both of them have CD's. The scanner will go through the entire process, but not be operable and doesn't specify the problem. The printer will not go through entire installation it says "can read the port not read properly" I have purchased different USB port and tried that with it, but still can't get it to complete the installation. Since that time I have installed both on my laptop because I need these for college, but would rather have them on my desktop. Any advice?

19 replies

by toivo talikka

Does the scanner also connect through USB?

Have you checked from the BIOS that USB support is enabled?

Did you re-install the operating system from a Windows installation CD or from an installation or recovery CD provided by the PC manufacturer?

If you installed Windows on your desktop computer from a Windows CD, did you install the motherboard drivers from the motherboard support CD? If you do not have the support CD, you can download the motherboard drivers from the manufacturer's website, or from the manufacturer of the motherboard, if your computer is not a brand name PC.

by grefan207

No, I didn't check the BIOS supports the USB, but I'm don't know how either. Yes, I re-installed Windows from CD provided by the manufacturer, but I didn't touch the motherboard.
If I go the the Compaq website for the motherboard what would it be called there?

I've tried all 4 exteral ports and it didn't work, but I could install them both on my laptop.

by toivo talikka

After you have powered on the computer, press F10 a few times and you should see the text "Entering Setup" or similar, and the blue and white screen with the BIOS options and the instructions how to exit and save the settings, or exit without saving the settings.

The option for BIOS support can probably be found behind a menu selection 'Advanced BIOS Settings' or similar. If the BIOS support has been off, there is no way your USB port would have worked.

If the USB support has been disabled, Windows will install the drivers automatically after you have logged in, assuming that your installation CD from Compaq contained the motherboard/chipset specific drivers.

From Compaq's or rather HP's website you need to locate the specific model of the PC. Their US website has Support & Drivers at http://www.hp.com/country/us/en/support.html?pageDisplay=drivers

I just realised that HP recommends a procedure "Application Recovery Process" for re-installing the original drivers, which do not seem to be available from the website, at least not for the HP model I checked:

"Use the HP or Compaq application recovery process to install drivers and software as follows:

1. Click Start, Programs, HP Tools or PC Help and Tools, and then click HP Application Recovery.

2. In Windows XP, select either Driver Installation or Application Installation and click Next.

3. Select the driver or name of software you wish to reinstall and click Install or OK.

4. Read and respond to any installation Windows that might appear."

by jeryba

hi '
i think you have som hardware problem with your laptop
you shood chak it

by grefan207

That was what I was thinking too, but if I take the sytem unit apart, I'm not really sure what to be looking for.

by kjell_andorsen

Like Toivo, I'm inclined to think this might be a USB controller problem. Have you checked Device manager to see if there are any existing hardware issues? Do you see an exclimation point next to any devices, especially anything related to the motherboard? If so, you will need to install the correct drivers to make your ports work.

by grefan207

I have to think that you two are right. I wasn't sure about a hardware issue, so I did as you said and this is what I found. There is a "?" next to Other Devices and a "?" with an "!" on top of Universal Serial Bus (USB)Controller.

I'm not sure what to do, "to install the correct drivers to make the ports work"

It seems like I learn more everyday with problems. Any help would be appreciated.

by toivo talikka

...about how to check the BIOS settings, enable USB support in BIOS, and how to re-install the drivers, if necessary.

by willcomp

Apparently you did not install motherboard chipset drivers after re-installing XP. That's the first thing you need to do after installing the OS.

Install chipset drivers. If you need help with drivers, post make and model of motherboard.

by grefan207

To my knowledge I didn't do anything to th drivers, but I'm open to suggestions. I'm not sure which number is the motherboard number, so I took them all day, figuring you might recognize it.
SP#252608-001 P52C50HREMNCWB
AS#253242-001 DG# 0011346-000

KSR1BA516 Spider S

686Y2 0005

LPC478367-NC

A0138-A939

8H106762

It also said when replacing compaq spare:
SPS-BDSYS W/NIC - SPIDER
246858-002

If you need me to pick one by location, or script or something, let me know. I left it disconnected.

by grefan207

I downloaded all of them that were there and it states printer driver is unknown. Don't know what else to do.

by grefan207

I went in and did a control panel, add printer, add printer wizard, picked the USB port, and had it proceed, by choosing the correct HP 7800 printer and the CD drive and told it to install. I suggested a test page, so I said sure, not holding my breath and she printed. I guess what you sent was what she needed. I really appreciate all the help. I'm not sure how to add numbers to your name for added support, but am willing if you advise. Thank you so much, I'm currently in college for IT and I think I learned more from you on this than my college class so far.

by grefan207

I tried your suggestion and ran into this. When I hit the F10 and got into the set up I found menu selection, but there wasn't one that had BIOS. I checked each tab. Therefore, I started to look for any that had I/O, ports, or printers to see if they were on. There was one marked I/O APIC Mode disabled. I changed that to enable. That didn't do anything, because I tried to enter the printer again and nothing, no ports was the repsonse again. I did notice this, but didn't know what it meant. under printer mode list it had EPP& ECP, what does that mean and is that right?

by grefan207

I didn't find where it actually states 845 chipset. I did however find this:
System: Microsoft Windows XP
Home Edition
Version 2002
Registered to:
Me
55277-OEM-0011903-00101
Manufactured and Supported by
Compaq
Intel(R)
Pentium(R) 4CPU 1.80GHZ
1.79 GHz
512MB of RAM
If the actual chipset number is what is necessary, how do I get it?

Sorry about being so naive.

by willcomp

I don't know how this new system works. I haven't asked a question to see what is involved is selecting helpful answers.

Will look around and see what I acn find.

by willcomp

How do I rate the answers to my posted Question?
Click on the answer. Click the Mark "Helpful" button displayed below the post. You may mark more than one answer as "Helpful."

This discussion is closed to new replies.