Discussion Locked

Terminal Services Printing Problems

0 helpful
4 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
We recently installed a VPN over DSL lines using SonicWall Firewalls. We use MAS90 accounting package & remote users experienced a significant reduction in speed while entering transactions. Our MAS software support suggested we have the remote users log in using terminal services, which we did. The speed problem was solved, but print jobs halted part-way through and would only finish printing after we clicked "OK" on an error message which displayed on the Win2K server stating that we are out of disk space, delete files to make more room. We have enough space. We then loaded a "Generic" printer driver for the Brother printers we use, and that solved the problem, but now this generic driver has caused other problems, namely the inability to print pdf files, or other non-MAS reports. I would like to re-load the full printer drivers, but avoid the error message on the server. Any ideas?

4 replies

by drbwaugh

Don't know is this will help, but we connect as term services client to a larger network and had severe problems printing until I delivered the drivers we were using on the local machines to the remote server and had them installed. The drivers on both the client and server apparently have to match exactly; the problem was that the server was running the correct driver, but an updated version. Hope this helps

by curacao_dejavu

We have been using terminals services for a couple of years now, and your are experiencing one of the issues with printing. Not all drivers are support in TS environment. Our standard is the hp 4l driver. You can try that and or try to download the newest printer drivers form the website of Brother or contact their support.

Leopold

by loungelizzard

Our organization uses a Citrix solution that had experienced the same issues surrounding matching drivers for both the server and client. To correct this problem and make things more simpler we implemented the "Uniprint" solution that has corrected and removed all problems of this type and has worked great especially if the printers are old,unsupported and no drivers. UniPrint lets you choose which printers your organization would like to use. Whether it is a low-end bubble jet printer, or a multipurpose machine, you'll always be able to print and immediately enjoy lower print-file bandwidth, fewer printer support calls and the freedom to use the mix of output devices that best suits your business needs. Best of all, you can accomplish all this without changing your current printing hardware or infrastructure. Services.

http://www.charon.com/uniprint/

by mgordon

We use Citrix in a big way and printing issues constitute about half our support calls. I can assure you the number of possible problems is legion; no one size fits all. The HP Laserjet 4 Plus drive is considered to be the "compability mode" driver and there's a slick trick to tell Citrix (and its MS counterpart, Terminal Services) to use a particular driver when it encounters a particular printer. I can say that some printers are just not very good candidates for Terminal Services or Citrix, and regretably Brother printers fall into that category, as does the lesser HP's (HP 1000 is very fickle with Citrix). The problem appears to be in "host based printers" where the host rasterizes the bitmap; text is not sent to the printer; just one big huge bitmap. In the Citrix environment, we consume about 17 megabytes PER PAGE of printed output when using a high resolution host-based printer -- you need a LOT of disk if you have host-based printers! You can minimize this problem by forcing all printers to 300 or 600 dpi (rather than 1200 or higher). In fact, reducing resolution is probably the cure for your situation. Also, beware the early disconnect -- many people will click on "print" and then disconnect their session before the report is "in hand." This can mess things up pretty bad on the spooler queues. One other gotcha; well -- two. Watch out for mapped client drives; if the client maps as "C:" (because your TS is NOT "C:") what will happen is that the spooler may attempt to use the client's disk as spooler storage, and it might indeed not have enough, to say nothing of performance problems. Viruses can invade the TS through mapped drives and installing a program when you've got mapped drives can leave bits of the application on the TS and bits of it on the client PC. Similarly, watch out for automatic importing of client drivers. It is a slick feature but a booby trap for the whole enterprise when a faulty print driver is uploaded from a client PC to

This discussion is closed to new replies.