Question Locked

transferring HD to another pc I think I did sonething wrong...

0 helpful
4 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

While transferring an already loaded HD with Windows XP, other programs and personal file I think that I screwed when I tried to do some changes to CMOs or BIOS. I mean, I had it going and except for for few unresponding hardware I/O
you could say I was really close to get it..Wrong!
After I did this change in the CMOs everything went bad. Now the only that I hear working is the
fans. There's no display and the CD-ROM, CD-DVD and Floppy drives don't even light up.
Please help me, is there any keyboard commands that I could try out. Any sgestions will be greatly appreciated!!! Thanks a lot

4 replies

by dawgit

Let's start at the begining, no better yet let's find a begining.
1 Working HD, with the OS, in a working computer. Correct?
You took that out and put it in another computer, as the primary HD. Correct?
It don't / won't work. again Correct?
If that's what you did, it won't work. Here's why: The HD you used (and the OS on it) had the drivers for the original computer that were set to load when started. Those drivers are now NOT the ones needed for the 'new' computer. Hence it can't boot, and doesn't reconize the hardware any more. ie: If someone were to take you in your sleep, from your bed, and put you in a different house, you will be rather confused when you wake up.
Solutions: (or possible ones) There must have been a reason you did that. The reason can determine which solution you can/should use. If the old computer is still useable, move all the files to an external HD, or disk (CD's or DVD's) then install the OS on the new computer, and then re-install your files. If the old computer is now total toast, and can no longer be used than that option is out. If you put the HD in the new computer and start the computer with the OS disk, it will give you several options. One will be Repair, another will be new Install. Here it gets tricky, Repair usually won't work because of the driver issue I mentioned above. (I haven't had luck doing it that way) You're stuck with Install. It will (Should) detect the 'old' OS, if the OS your loading is 'Newer' or 'Equal to' the old OS, you won't have a problem. (you can't take a disk with XP for example, and try this with Win98, it won't work) It will (again, should) ask you if you wish to keep your set-up/files or wipe and start over. (It's best here, to Wipe, and start over, but you'll lose your files) Pick the keep the old stuff options if you must, and re-install.
Keep in mind that you may need to have (as in buy) a new licence (as in Software also) for the OS you'll now be useing, as it is on a new machine.
Does any of that help? -d

by ryankwancortes

please check your power supply... try to open the power case then see if your capacitors are blown or leak. if you see them.. replace power supply. the reason why no power ..of your cdrom, dvd, floppy or other components inside your computer.

or is not enough power to supply those components. try to upgrade your power supply instead.

by thechas

Since things went awry after you made some CMOS settings changes, it is likely that you made a change that the hardware does not support.

The easy thing to do, is a CMOS reset or clear.

Check the motherboard manual and locate the clear CMOS jumper.

With the PC off, set the jumper to the clear setting.

Power up the PC. (at least attempt to)

Shut down and set the jumper back to normal.

You should now be able to boot up again.

Cautiously set the BIOS settings. Make sure that you understand EVERY setting before changing from the default.

Now, you likely have a lot of work ahead getting Windows to function properly.

Have all driver files either downloaded (and extracted from archives), or the CDs at hand.

Open Device manager, and remove EVERY hardware device that is either not correct, or has a yellow "!" or "?" mark next to it.

I install drivers in this order:

Chip-set (motherboard)
Video
Monitor
Network
Modem
Sound

Other devices.

Reboot as recommended.

Next, to clear out the old hardware from the old system, you need a good registry cleaning.

If you understand the registry, you can do this manually. Keep in mind that registry edits are more dangerous and harder to recover from than BIOS setting errors.

If you want to use a commercial registry cleaner, try Registry First Aid from Rose City Software, System Mechanic from Ilio Systems, or Fix-It from V-Com software.

Chas

This discussion is closed to new replies.