Discussion Locked

Why have I failed to install Red Hat on

0 helpful
11 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Dear Friends,
My name is Michael and I live in the United States.
I am taking a step towards a carreer in LINUX and I have a few books to
help me get a good fundation. This afternoon I took the challenge to install
my first system but did not succeed. I encountered a technical problem and
please I need help from someone out there.

Just to give you a little backgroud to my system, my computer's CPU is Pentium
with 133MHz speed. mY CDROM functions very and I was able to use my Red Hut CD
to boot the system.
However, I heva just installed a new hard disk. It is an IDE 40GB 5400RPM ATA100
manufactured by Western Digital. I partitioned it into four 10GB partitions
using the manufacturer's disk intallion utility and also installed
Windows 2000 Profesional. Windows is running very well. But when I boot the
system from the CDROM in an attempt to Install LINUX (RED HAT LINUX 6.1)
the OS's instalation procedure fails to locate the hard disk. Below is the
Error message:-
FDISK ERROR
AN ERROR OCCURRED READING THE PARTITION TABLE FOR THE BLOCK DEVICE hda.
THE ERROR WAS. NO SUCH FILE OR DIRECTORY.
what is the problem ? Does the linux have any problem with FAT32?
I am stuck please give me some technial advice.

My email address is mukonect@mailcity.com
Michel

11 replies

by aaube

Are you sure the disk is FAT32 partitioned? Windows 2000 (like NT) may have a different disk partitioning scheme. Also, the manufacturer's partitioning software may be a proprietary partition table. Either way, Linux might not be able to read it.Also, when installing Linux, have some unpartitioned space available because Linux uses its own partitioning scheme. This probably isn't the cause of this problem, but you may encounter it later after you get past this one.

It also depends on which version of Red Hat you're using - older versions won't be as compatible with other partitioning schemes as a newer version.

My suggestion: delete all partitions from the drive. Install Linux first, leaving unpartitioned space for Windows 2000. Then install Windows 2000 on the remaining space.

If you don't want to wipe the drive completely clean, at least delete the partitions you aren't using. This may help.

by krkosiorek

There is a good chance that Linux will not recognize partitions that were not created with it's partitioning utilities(fdisk or Disk Druid).

One way to dual boot Windows 2000 and Linux is to do the following:
-Boot the machine using the Linux install CD.
-Delete any current partitions.
-Use fdisk to put a small (request 16 MB - it will make a partition of 22 MB) Linux native partition at the begining of the drive. Reason: the BIOS of some machines can not boot from any sector of a hard drive past 1023.
-Write this to the partition to the disk (you will use the partition later for the /boot partition of linux).
-Don't go any further into the install program, reboot the machine.
-Insert the Windows 2000 disk and boot from that.
-Windows 2000 install will see the small partition as unknown. Create the partition that you want to install Windows on (best to make it the partition after the small partition) and any other partition that you want to be NTFS. You can also create aFAT 32 partition that can be seen by both Windows and Linux.
-Install Windows on the partition you just created formatting it NTFS.
-Once Windows is installed, boot the computer using the Linux disks and create the remaining partitions(usually /root and )needed for Linux. Assign the 16 MB partition to be /boot.
-Later in the install, specify that LILO be installed to the first sector of /boot !!NOT THE MBR!!.
-That is it for the Linux install. You won't be able to get to Linux without a boot disk until you read the following article. Steps 5-7 are the most important in this case. http://www.linuxdoc.org/HOWTO/mini/Linux+NT-Loader.html

I have a Western Digital 40GB 7200RPM ATA-100 drive and it worked great for me.

Hopethis helps. Good luck.

by brhynsburger

Honestly it is easier to install windows then Linux but like everyone said you have to leave some space open for Linx to call home. I would dump all partitions Load a 5 gig partiton for windows load windows then come back in with Linux and make yourLinux partitions You really only need a minimum of 2 partitions for linux a / and a swap. This is not the best but it is the easest course of action. Then allocate the rest of the hardrive however you see fit.

Word of advise buy another harddrivefor linux need not be any bigger then a couple of gig and use one for windows and one for Linux you will be happier trust me.

by a.c

You have got your hard disk as the primary master ? (i.e. hda)
Good..
Simple partition scheme
1st primary 100-200 meg this is your / (root) directory for Linux, this is plenty large enough most of the time.
2nd primary 10 gig for win2k (not got XP RC1 yet ?)
make the rest of the disk an extended partition (just under 30 gig)
add 5 logical drives
1, 5 gig (ext2) mount on /usr
2, 5 gig (ext2) mount on /home
3, 128-256 meg (swap)
4, 10 gig (FAT 32)
5, 10 gig (or whatever is left) (FAT 32)

you might want to use something like partition magic to do that lot.

Install Linux after Win2k and use LILO on the MBR makeing sure you have set it correctly to boot to the first partition for linux and the second for win2k.

Just to show you that this all works I have 2 systems, one with win98 and redhat 6.1, the other has winMe, Linux and win2k (which has just been upgraded to XP) this machine has a total of 10 partitions on a 30 gig drive with most being logicals (including the NTFS part that XP is on)

A.C.

by a.c

forgot to mention the reason for the small root is to keep the bottom of the second partion within the 1023 boundry, the reason you can get away with having three OS's and sling win2k up the top is that it's loader sits on the winMe C: drive which is down the bottom end of the disk (all of which sounds terrible, but works a treat!)

by a.c

One last thought, you mentioned that you used the installation utility to partition the disk, would that also suggest that possibly you are having to use a disk manager to aloow your machine to see a 40gig drive ? If you have not got direct support for your drive in BIOS, this could cause problems with Linux.

This discussion is closed to new replies.