Discussion Locked

Win '98 machine not showing up in Netwk

0 helpful
21 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
I have a mix of '95 and a couple of '98 workstations on a small 10-node, through a hub peer-to-peer. One of the '98 stations needs to be accessed by one of the '95. All of the computer names show up in net neighborhood except one (only one) of the'98 machines and it's the one I need to show up. Yes, I have File and Print Sharing started, same workgroup, everything the same, tried Netbeui, TCP/IP, reinstalled all networking, have drive shared, changed network card, to no avail. TCP/IP settings are correct (subnet, etc.) I've never seen this before and am pulling my hair out. Also have tried LanMan announce, Master Browser disabled, enabled. The '98 stations can see all others fine, but no one can see hers. She is logged in correctly, too. Help.

21 replies

by ahttech

Not really an answer, but some other things to check. If you do a Find Computer can you see it? What version of 98? If original, have you applied service packs? Are you getting a link light at the hub (bad cabling)?

by bryan bowers

Couple of things to try:

Try pinging the computer from another workstation. If it doesn't respond, then your IP is setup incorrectly. Check your default gateway, subnet mask, etc..

Try connecting to the computer using UNC (\\computername). If this doesn't work, you might have a bad network card.

by jpereira

If your network is not working (you can't ping other people from the PC), check all the hardware i.e. all cabling and sockets - replace with a known working connection, hub - I've seen hubs with one bad port on them, network card - swap it with one from a working machine and see if the problem follows it.

If you are certain the network is working, my only suggestion is to check that the user has actually shared some resources. Computers don't show up in net neibourhood unless there is something on them (a directory or printer) shared.

by tysonmathews

from another machine on the network do a ping. Just because it is not in Network Neighborhood doesn't mean it isn't there. Also check your workgroups. Also the machine that you can not see, Can it see the others? Is there an IP conflict? NetBuiInstalled?

by chipmunk

I had this happened a few times. I would check everything and find everything set properly.
So I shut all the computers down within that network. Turn the biggest one first and when that is up, start turning the rest of the pc's on within that network.
The reason I did this, I want the biggest system to take over as the master browser.

Good Luck.

Alvin

by chipmunk

I had this happened a few times. I would check everything and find everything set properly.
So I shut all the computers down within that network. Turn the biggest one first and when that is up, start turning the rest of the pc's on within that network.
The reason I did this, I want the biggest system to take over as the master browser.

Good Luck.

Alvin

by todd o.

For a quick an dirty solution, why not add an LMHOSTS file that contains the information to find the missing computer? At a minimum, trying that will help to narrow down what is wrong (if the LMHOSTS file doesn't solve the problem).

You can findinformation about setting up an LMHOSTS file at step six of this page: http://winfiles.cnet.com/howto/peercon.html

by white wolf

First, you might want to check that the computer/machine name is valid, (no spaces, punctuaction and such). Does computer see itself in the neighborhood? If not, mark sure is it's setup with same client as the others (Microsoft and Novell's file & print sharing services do not mix).

You could have a corrupt driver that's failing to be replaced. I've found sometimes you have to uninstall and reboot first, then try to reinstall the protocols & drivers. But sometimes windows will hang on to those corrupt drivers a like bulldog with lockjaw, and you won't be able to remove them while in windows: you'll have to know the exact filenames & locations and delete manually them while booted to DOS.

Good Luck!

by zuzamar

Check and see if the person using this machine has named the hard drive and added an $(dollar sign) after the name. If so remove the $. The $ addition is a way to hide a drive from others on a network.

This discussion is closed to new replies.