Discussion Locked

windows boot disk

0 helpful
5 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
I,m new. what files can i copy onto a floppy to make it a boot disk so i can boot from a formatted fdisked drive.

5 replies

by tech_wiz03

If your talking win98 making an emergency boot disk , you can use the bootdisk function from with-in windows. If you don't have this ability you can format the floppy with format a:/s/u/v to format and tranfer the system files to the drive then copy fdisk, format and make a config.sys autoexec.bat that will resognise and load drivers for your cdrom. you will need the mscdex program and your cdrom driver as well for cdrom support.

hope this helps
rick

by thechas

Step 1:

Format a floppy and copy system files / make bootable.

If you are running Windows 98 or XP, you can create a boot disk from within Windows with no problem.

For W98, go to Add / Remove Programs and click on the startup disk tab.

For XP, right click on the floppy drive from either Windows Explorer or My Computer and select Format.
Select the option to create a bootable disk.

For other options, check out:
www.bootdisk.com
www.madboot.com

Note: the version of fdisk that is on a W98 disk does NOT support drives larger than 64GB. You need to download the newer version of Fdisk from Microsoft.
However, this version only supports drives up to 132GB.

From your boot disk, run fdisk and partition the drive as desired.
www.aumha.org
www.fdisk.com/fdisk

After you exit fdisk and re-boot, run the format command for at least the C: drive

format C: /s
the "S" switch copies the system files from the floppy onto the hard drive.
This along with making the C: drive active in fdisk makes it possible to boot from the hard drive.

Chas

by mark

Start, Run, Type in "Command", Press OK.
At prompt, type "SYS A:", press Enter.
You now have a bootable floppy.

by dmiles

Follow these steps to create you own Windows 95/98 boot floppy disk:

Start up your system normally and go to Start/Programs/"MSDOS Prompt"
Insert the floppy disk in the drive A.
Setting up the floppy disk/copying the needed files From the DOS prompt (it should be C:\WINDOWS>) type:
FORMAT A: This formats the floppy disk.
SYS A: This makes the floppy disk bootable.
COPY HIMEM.SYS A:
COPY EMM386.EXE A:
COPY SCANDISK*.* A: Useful for troubleshooting.
CD\WINDOWS\COMMAND The prompt should change to C:\WINDOWS\COMMAND>
COPY FDISK.EXE A:
COPY FORMAT.COM A:
COPY SYS.COM A:
COPY EDIT.* A:
COPY MSCDEX.EXE A: Needed for your CDROM drive in DOS
Copy your DOS CDROM driver file (C:\?????\?????.SYS) to A:
COPY DELTREE.EXE A: (Optional)
COPY MEM.EXE A: (Optional)
Create startup files on the floppy: (Still from the C:\Window\Command prompt)
EDIT A:\CONFIG.SYS this will open a new file named config.sys on A. Save the file when done. This file should contain these lines:
DEVICE=HIMEM.SYS
DEVICE=EMM386.EXE RAM
DOS=HIGH,UMB
FILES=100
BUFFERS=20
DEVICEHIGH=????????.SYS /D:OEMCD001 (To load your DOS CDROM driver)
EDIT A:\AUTOEXEC.BAT This file only needs one line, save it when done.
LH MSCDEX.EXE /D:OEMCD001 (To also load for your CDROM)

This discussion is closed to new replies.