Discussion Locked

169 ip address on window vista

0 helpful
10 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

one of my clients system on vista connected to wireless netgear router and intern connected to comcast modem
when i do ipconfig /all
generates 169 ipddress i have tried releasing renewing (doesnt work ) power cycled router and modem ,rebooted machine did netsh winsock reset , still the same .
but i connected directly visat to modem able to cvonnect to internet (192 ipaddress ) .

can anyone explain me the reason and also the fix

10 replies

by cg it

if you can connect directly via modem, stick the netgear in and not connect, netgear problem.

169 is APIPA [automatic addressing] which means that the netgear router isn't providing your system with an address.

try diabling IPv6 on your computer.

by yakuz4

You need to make sure that the wireless security settings are configured the same as in the netgear router. Connect using RJ45 cable and enter to the Netgear router page to checked on the wireless settings especially the security type & security key/passphrase. On Vista you can retype the security key again as the one on the router. If necessary remove the current wireless connection and recreate it back.

by akdhingra

hello
nawanan
how r u. i am from india. can i email you. send me your email amit.dhingra at akdcompanies.com

by abhijit.sil

This fix worked man. Even my provider messed up & concluded that I have a faulty Wireless card. This fix took 5 mins to fix my issue. Great job man. Thanks,

by coolguy_5620

this is has happened once and seemed to be a issue with the netgear built in firewall disable that it should work

by t_spitt

You are trying to use your wireless and LAN make sure that you unplug the router while you have a direct connection. Your PC /MAC is confused on which connection to connect with. YOU CAN ONLY HAVE ONE....wireless or LAN...Ethernet or USB. If you are pulling a valid IP it would be a 97.XXX.XX.XXX or 66.XXX.xx.XXX not a 192.XXX.XXX.XX/ 192.168.100.XX (mdm)192.168.1.XX(rtr) 169.XXX.XXX.XXx(default from PC/MAC).

by kathie_davis

Most home networks today will consist of a broadband modem, a router and one or more computers that share that Internet connection. The router has two IP addresses: An exterior IP address seen by the outside world and an interior IP address seen only by the computers on the local network. Your ISP assigns the router it's exterior address, which may be something like 69.x.x.x (where the Xs are numbers).

The router will then give each internal PC its own local address, usually something like 192.168.1.2. Other PCs will have an address similar to 192.168.1.3, etc. In this case the router is considered the DHCP server and the gateway to the Internet. When you boot your machine, the computer will broadcast a request for an IP address and the router will normally answer. If it does not see the DHCP server it will give up and make up an IP address for itself. This IP will often look something like 169.x.x.x. This is a local address that will not likely have any communication with other PCs on the network.

We mention the 169 IP address because people will suddenly lose Internet connectivity when it worked the previous day. An easy way to attempt to fix this is to just reboot everything?modem, router and PCs.

In XP you can check your IP address by going to the command line. Go to START>RUN and type cmd and hit Okay. Next, type ipconfig /all and hit Enter. You will be able to see a lot of information about the gateway and the IP address of the computer. The IP address should be similar to 192.168.1.2 with a subnet mask of 255.255.255.0. If you have the 169 IP address, we can try the reboot.

Follow these steps in sequence:

Check IP
IP is 169.?.?.?
Place Local area connection in DISABLE...
Take the Coax cable off the modem
Place Local area connection in ENABLE
Check IP
If IP is a 192.?.?.? (192.anything.anything.anything)
Then proceed
Place Local area connection in DISABLE...
Re-attatch the coax cable to the modem
Place Local area connection in ENABLE
You should now pull a public IP; 68 - 74.?.?.?

by dan241982

hey sooraj could please reply as to which of these alternatives worked, as i'm facing the same problem.

This discussion is closed to new replies.