Discussion Locked

2 Power supplies in a system...how-to?

0 helpful
9 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Hi,

I have searched this from couple of days on the net but still not found what I want to do....

I just want to know that can i add 2 power supplies in a system running simultaneously & dividing the components of the system on these 2 power supplies.........?If it is possible, then how can i do this......connecting the 2 power supplies to mainboard & when press the power button from one power supply the 2nd power supply also on by doing this...........?

Any help / info / idea...........?

if my question is not clear or need any further info then let me know..........

Awaiting helpful reply as always....

Regards / Sulman

9 replies

by oldefar

The most common approach is multiple external power supplies with their outputs connected to a barrier strip. The barrier strip provides a mechanical common connect point for each power supply by voltage, placing them in parallel. The equipment being powered also connects to the barrier strip. Current load auto balances across the power supplies.

Primary AC for each power supply, and the associated ON/OFF, is generally left independent to facilitate maintenance of a single power supply. The attachments to the barrier strip can be connecterized as well to ease maintenance.

A single ON/OFF switch can be established by using a common AC point - for example a power strip with an ON/OFF switch.

by timwalsh

There is no simple way to do this on your own. If you don't know exactly what you are doing (and aren't an accomplished electrician to boot), you are risking frying all of your components.

Why not just buy a system case that includes dual power supplies. There are many on the market for use in server and high-availability applications. All the circuitry needed is already included with the case.

by mrafrohead

But wouldn't the motherboard have to support dual power supplies also???

Another thing. How is one PS going to know the load on the other PS and be able to compensate for it if the mobo doesn't support dual connections???

Mrafrohead

by oldefar

The motherboard is only looking for TTL connections of power ground, +12, -12, and +5. Whether the power comes from an internal power supply or external power supply is incedental. The power switch is really an inline switch on the AC.

You can consider the power lead mounting screws on the mother board as a barrier strip. Simply a common point of connection. I would tend to use a seperate barrier strip and run the power in leads from the device (as in motherboard) to the barrier strip.
The power supplies provide current based on a constant voltage and a resistance (I=E/R). In a parallel circuit, resistance is reduced by the paths so each power supply will provide half the current requirements - load balancing. Of course if the voltages are off, the current on each will vary a bit. Today's power supplies typically use solid state voltage regulators that require no adjustment and are within a fraction of a percent of their stated voltages.

We used to do this with the olddiscreet component computers and communications equipment on a regular basis. That was with power supplies that required field adjustments and had drift ranges of 5 to 10 percent.

by mallardtooxx

Why do you need dual ps? I mean is there a dire need or is this just something you are curious about? So far these guys are right on olde is right you can do the external bus and there are dual ps mb's and cases...I just want to make sure that is what you are looking for =)

duck

by thechas

First, why do you want dual power supplies?

Second, what type of system do you have?

The suggestions for wireing 'could' work for an AT style supply that uses a hard wired on/off switch.

For an ATX system, you will need at a minimum to design a circuit to split and isolate the turn-on and 5 volt standby lines.

The paralleling concept works fairly well with analog discrete power supplies, and bench type switching supplies. I'm not confident that it would work with the switching power supplies used in PCs.

Concerns:
PC switchers need a minimum current draw to stay running. If one supply has a slightly higher output voltage, the other supply may shut down.

Most switching circuits are not designed to be back-fed. If one supply has a quicker startup time than the other, the supply with the slower startup time might just blow up.

Also, if one supply goes (fails), it WILL take the other supply with it.

This scenario reminds me of an engineer I once worked with. Hewas certian that he could cross wire 2 variable AC auto-transformers to get the 220 volts he needed. We nick-named him smokey!

Chas

by sulmau

Hi,

I'm very thankful to all of u that u answer my question in detail.

The question that why i want to do this is that I was just thinking that is it possible to purchase the system case without dual power supplies & do it myself........

Regarding what type...... I'm currently working on both AT & ATX to develop the 2 power supplies in a single case...........

Thanks again 4 all the help / info / idea.
If someone have any other idea then please let me know.

Regards / Sulman

by mrafrohead

This project sounds more difficult than I would have thought it to be.

How may I ask is it that servers generally come with dual power supplies. Either as a boost in power or for redundancy???

Personally I would love to have two power supplies in my computer. I think that having two would be better than having one big one as it would take the strain off of just one during a huge workload. Ie... burning cd's, playing a game with a large vid card, moving data around and accessing your floppy at the same time.

Mrafrohead

by admin

It's not that hard if you are handy with sheetmetal and electronics, but what's your point?
You could share two smaller ones, one to drives, one to mobo or fans or whatever if you want extreme isolation etc. Redundancy is another use which isn't hard to get info yourself on if you actually want to do it yourself. I would just say that you have to remember cooling and that it is probably cheaper and easier just to buy a redundant set-up or hit your local computer scrap lord and they will probably set you up REALLY cheap since few people need old redundant set-ups.

If you have another use... post it :)

This discussion is closed to new replies.