Discussion Locked

98 comp. unable to obtain IP adresses

0 helpful
18 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I have a 4 computer network w/NTserver, there is a computer that is running WIN98 upgrade (first edition), there is a DCHP + WINS on the server.
the computer cannot get the ip adresses or host names of the other computers on the network, they all have static adresses set by the DCHP and are logged in the WINS server.
the computer comes up with the error : "there is no logon server to service the logon request"

ne ideas whats worng and how i can fix it?

Sam

18 replies

by gperrie

Check the PC is getting an IP from the DHCP server. I think in 98 the command is winipcfg.
If it has an address, try a manual refresh to see what happens.

Gavin

by mightyyoungfai

you can always check the ip from winipcfg, select your nic and then release it and renew it. if this can't help i think you have to manually add the ip from the network properties.
1. select tcp/ip -> nic
2. choose properties and specify the address manually
3. then choose the wins configuration tab, and enable the wins resolution.
4. restart then see the changes

hope this will help

by brothertech

Do answer #1 first.

If this doesn't work then you might have a corrupted NIC TCP/IP driver. Verify the type of NIC you have. Have your windows CD available. From control panel/networks remove the NIC and TCP/IP. Reboot, your computer may locate the NIC again which you will install the NIC driver. THe computer WILL ask for your disk (or locate a copy on your hard drive). This should fix your problem. If not then you might have a bad NIC.

by jenral_sam

The computer is quite old (made in '94), but it can still get to the server and logon copy files etc...

sam

by pacalealaathotmail.c

as far as i can see
you have at least two problems:

1. in a small network a ws (W98) does not get an IP from a NT server.

2. browsing the network your ws (W98) gets to display an error message when trying to access other computers from the neighborhood

what was your question again ?

by jenral_sam

1. yes it does, there is a winNT server on the network and it does obtain an ip from it.
2. you have a talent for confusing people :-)

sam

by hazzard_005

It seems that the machine can access the server but not the other computers. Correct?

You also stated that you are using static IP's. Correct?

I would Check the IP settings on the new machine and make sure that the "dynamic" ip address is onthe same Subnet as the other machines. Or set the 98 machine up with a static IP address and subnet which matches the other machines.

It just seems that the problem is based on a subnet or gateway setting.

I hope I Helped and understood theproblem enough to help.

by 1stladytech

Are all client machines running Win98, or are the others under a more current OS? If you have Win2k or WinXP on the other machines, you have to set up a user account on the workstations for the Win98 machine to be able to access them. If you couldprovide more info it would be helpful.

Vickie

by randalbin

Check the computer's IP in Winipcfg to see if it is within the scope of the DHCP server. Win98 will assign it's own private addressing scheme if the DHCP server does not happen to be available at login time. Machines using Win98 private addresses cannot communicate with other subnets. I have had trouble getting Win98 machines to release these private addresses even when rebooting or specifying release and renew. Specify a static IP address and subnet mask that is on the correct subnet as theother machines and reboot. Once the computer has established this IP and can communicate on the network, you can switch back to "Obtain an IP address automatically".

by wlbowers

If you have everything right in the network
configuration panes, Log on to server, win, ect.
You can try to use the host file. There should
be a sample in the windows directory. If not
you can create one with notepad. it is simple
to use. You enter the tcp/ip address, space or
tab, then the name of the machine that utilizes
that address.
Example:
10.0.0.2 server
10.0.0.4 Mike

Once you have finished the assignments save
it as text. Then go back and delete the .txt
extention. The file will just be named host

Microsoft added all of the information
assignment panes in networking but it still at
times reverts to dum as dos.

Good Luck Lee

This discussion is closed to new replies.