Question Locked

Acer Aspire with Vista-can't set up wireless - cuts out

0 helpful
13 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
I have an Acer Aspire 7720-6208 with Vista and my connection is the strongest - I am right by my router but it keeps switching to some other person's network then at times I have no connection but looking at the little triangle I have a good connection but can't access it. I did not know how to set it up so no wonder it does strange things. I didn't even know where to begin. If Acer has its own wireless set up I want to use that one. Is there a list someone could give me that says, first you do this, then this, etc. so I can access my network which is the strongest using Acer's and not Windows's set up? It is probably very easy but when it oomes to wireless, I am very ignorant. Janice.

13 replies

by nepenthe0

http://tinyurl.com/2ugq55

Also, carefully review your router User Guide for the correct setup. In addition, look over the following checklist:

1) Check the signal strength by hovering the mouse over the wireless network icon in the system tray. If the signal strength is low, that is the most likely reason for a dropped connection.

Wi-Fi is short range 2.4GHz radio, essentially worthless beyond 150 feet from the access point. Here are some tips that may help reduce dropped connections:

2) A vertical booster antenna for the router can enhance horizontal coverage by ~50%

3) If the router is located one floor up or down from the laptop, consider relocating the router to the same floor

4) If the wireless adapters are 802.11g, program the router to broadcast only in G mode. Disable multi-mode broadcasting.

5) Enable SSID broadcast in your router setup

6) WPA encryption is more squirrely than WEP, but WEP is less secure

7) How important is encryption for you? If there are no likely snoopers within 150 feet, consider disabling encryption. With encryption disabled, connection is faster, data transmission faster, and there are fewer dropped connections

8) If you disable encryption, it would be wise to enable the MAC address filter in the router setup. Enter the MAC addresses of the wireless adapters, and the native MAC network card addresses of any desktop computers

9) If you disable encryption and enable MAC address filtration, periodically check for intruders. With Linksys, open the router setup, and navigate:

Status > Local Network > DHCP Client Table

The only MAC addresses posted on that table should be your own equipment. Any other MAC address is an intruder, and you can banish that person by adding that MAC address to the naughty list:

Wireless > Wireless MAC Filter > Prevent PCs listed below from accessing the wireless network

10) check for 2.4GHz radiofrequency interference near the laptops (cordless telephone base stations)

11) check for RF interference (fans, motors, hard drives, etc.)

12) check for shielding (metal cabinets, etc)

13) If still no connection, try disabling the proprietary driver and enabling the default Windows wireless chip driver.

14) Configure the router to automatically obtain IP address from DHCP.

15) Look for a strong signal (>50% signal strength) from a channel close to the router's assigned channel. There should be 5 channels between such signals to avoid interference due to bandwidth issues. For example, if you see a strong signal broadcast on channel 6, program the router to broadcast on channel 1 or channel 11.

16) Check your laptop power management. Is there a timeout for the wireless adapter? If so, configure your power management so that the wireless LAN is always enabled and powered.

17) You may have to do some acrobatics to get everything stable once properly configured. This is the sequence that has worked for me:

17a) Disconnect the Ethernet cable from the cable modem
17b) Boot the modem
17c) Boot the router
17d) Reconnect the router-modem Ethernet cable

18) If all else fails, consider Network Magic:

http://tinyurl.com/66x5cn

That about exhausts my suggestions. You may legitimately need encryption, but be aware that there is a penalty to pay for the complexities of this technology. If there are no likely snoopers within range of your access point, and you utilize MAC address filtration, and you are not overly concerned about the sensitivity of the wirelessly transmitted communication, your wireless connection will be more predictably successful by disabling encryption.

Rick/Portland, OR

by jchadola

Thanks Rick. A lot of what you said is beyond my current capabilities, but I've gone the Network Magic route and I couldn't even get it installed. My laptop is about 5 feet from the router and the router and modem are combined. It's a 2Wire modem/router which I have because it is the only one my ISP supports - before I had any laptops there were ISP problems and I had to have a guy from Telus out and he did something a few blocks away and it fixed it. This was pre-wireless so I suppose it could be an ISP problem. Believe it or not I have 4 laptops and a desktop - I can't pass up a good deal. The LG is finally being properly repaired. My HP laptop had to be sent to Ontario to be fixed. I can't recall the problems it had but I got the blue screen of death on that one. When I got it back, the wireless connection wasn't bad - I am considering buying another router/modem. The disconnecting you suggested I've tried with no luck - I got the blue screen of death tonight after I unplugged everything. I hoped Network Magic - I've got the premium edition - would save me but it wouldn't install. I think the authorized service depot is the same place that my LG laptop is finally being repaired. I can't print from my laptop - I could earlier tonight - I wanted to print these responses but now I can't. It is so frustrating. Sometimes, if you get a good tech, it is better just to hand the thing over to someone else and say "fix it".

by jchadola

Amidst my computer misery, I had to laugh at how they describe my occupation - legal/medical. I am a lawyer but on long term disability from smashing my face on a concrete sidewalk resulting in balance problems and double vision among other things - so I guess there is a medical connection.

by older mycroft

Hover over the signal meter in the systray and right click on it.

Now, bear with me, I still run my Acer with XP but I've seen Acer's running Vista, so when you right click on the signal icon you should have a menu item allowing you to view available wireless networks. Click on that item.

You should be presented with a list of ALL the wireless access points available that the Acer can 'see'. Select YOUR wireless signal by left clicking and you should also be able to stipulate THAT signal alone.

You can also get access via Control Panel (in Classic View) by clicking on Networks and selecting Wireless Network.

Either way, you need to get to the screen that shows you tall the wireless signals from which you emphasise which one alone you want to be connected to.

The problems you describe of jumping to a signal that is strong but does not give internet access - this is the signal of a wireless router that is either:

#1 Secured with encryption, unrecognised by your Acer
#2 Emmitting a wireless signal but not actually online. Only the host computer can place it online.

Sorry I can't be more specific but it WAS about 5 months ago that I last saw Vista on an Acer. ;)

by jchadola

Even though I've only used it for a few weeks, everything is worse now. I've been getting 2 of everything whether I've managed to get a wireless connection or not. If I start internet explorer, I get 2 separate screens. I get 2 of every email. Even if I manage to use my own wireless connection which is secured, it cuts out on me and the same thing happens when it isn't a wireless connection. I get error messages when I try to send emails a lot of the time. I think Acer has their own way of connecting wirelessly - it looks that way but I do not know how to. Then just a while ago I got the dreaded blue screen of death. It had a whole screen of printing but it switched off so fast all I could see was that the computer was turning itself off to protect the computer - then the screen went black and it restarted and I briefly had a wireless connection then it died but it works except for double of everything when I don't use it wirelessly. Right now I was going to try system restore which I have never had much luck with on other computers -then I was considering doing a system recovery. I ordered the recovery CDs a couple of weeks ago and have those. I have the strangest things happen with my computers. I really enjoy them when they work - I have an LG laptop with XP on it at an authorized service depot because it wouldn't read my XD card and I lost my sound and the techs did nothing and were going to charge me $600. In fact it developed another problem which I corrected. Now it is with the Operations Manager who asked me if he could use my situation as an example for teaching better customer service. I just have no luck. And yes, I got 2 of this post and 2 of the other one. Janice

by older mycroft

"Even though I've only used it for a few weeks, everything is worse now. [b]Does this mean that the Acer is brand new (minus a few weeks)? In that case you're still under warranty![/b]

I've been getting 2 of everything whether I've managed to get a wireless connection or not. If I start internet explorer, I get 2 separate screens. [b]Now you've lost me - how can you get 2 screens? Do you mean that IE is opening TWO framed windows, one on top of the other? Can you expand on this phenomenon as I'm not sure what you mean.[/b]

I get 2 of every email. Even if I manage to use my own wireless connection which is secured, it cuts out on me and the same thing happens when it isn't a wireless connection. [b]Two things spring to mind here:

#1 How EXACTLY are you choosing between wireless & wired? Are you just switching the wireless system off by using the hardware switch on your laptop, so that the indicator light goes out? - If so, you may be causing your own problem: you should be accessing your Networks screen and disabling the wireless connection BEFORE you enable the wired connection. There is a possibility that you are connecting to the internet TWICE simultaneously; once on your wired connection and once wirelessly. Strictly speaking your CAT5/6 cable should not be connected if you are using the wireless connection.

#2 When you are connecting to the internet via your LAN (wired), are you still getting error messages? The blurb above also applies here.[/b]

I get error messages when I try to send emails a lot of the time. [b] How do you send emails - what email client are you using?[/b] I think Acer has their own way of connecting wirelessly - it looks that way but I do not know how to. [b]This is an interesting point - the Acer may still be populated with 3rd party internet software. Depending on what your ISP is, you should check the Acer with 'Add/Remove Programs' to ensure there is NO other ISP software installed.[/b]

Then just a while ago I got the dreaded blue screen of death. It had a whole screen of printing but it switched off so fast all I could see was that the computer was turning itself off to protect the computer - then the screen went black and it restarted...[b] You can stop the Acer from restarting, so that it will halt at the BSOD so that you can read and absorb what it says. [u]My knowledge of Vista is marginal at best but this should still work:[/u] you need to get access to your 'System Properties' to stop Vista from Automatically Restarting on System Failure. I don't know how to do that on Vista but will find out when I've finished typing this reply.[/b]

...and I briefly had a wireless connection then it died but it works except for double of everything when I don't use it wirelessly. [b]- I think I may have already covered this point.[/b] Right now I was going to try system restore which I have never had much luck with on other computers -then I was considering doing a system recovery. I ordered the recovery CDs a couple of weeks ago and have those. [b]System Restore is not quite necessary yet.[/b] I have the strangest things happen with my computers. I really enjoy them when they work - I have an LG laptop with XP on it at an authorized service depot because it wouldn't read my XD card and I lost my sound and the techs did nothing and were going to charge me $600. In fact it developed another problem which I corrected. Now it is with the Operations Manager who asked me if he could use my situation as an example for teaching better customer service. I just have no luck. And yes, I got 2 of this post and 2 of the other one. [b] I'd be grateful if you could expand on this last point. How, or more importantly WHERE are you receiving these double copies of each email / browser image. I am having great difficulty trying to imagine just what this looks like.

Bear with us - it's all in the detail. Your current problem is one of the most interesting I've heard this year![/b] ;)

by older mycroft

This is how to stop Vista from snatching the BSOD from you and restarting right away:

1. Click on Start and then Control Panel.

Tip: In a hurry? Type system in the search box after clicking Start. Choose System from the list of results and then skip to Step 4.

2. Click on the System and Maintenance link.

Note: If you're viewing the Classic View of Control Panel, you won't see this link. Simply double-click on the System icon and proceed to Step 4.

3. Click on the System link.

4. In the task pane on the left, click the Advanced system settings link.

5. Locate the Startup and Recovery area and click on the Settings button.

6. In the Startup and Recovery window, locate and uncheck the check box next to Automatically restart.

7. Click OK in the Startup and Recovery window.

8. Click OK in the System Properties window.

9. You can now close the System window.

10. From now on, when a problem causes a BSOD or another major error that halts the system, the PC will not automatically reboot. Rebooting manually will be necessary.

Post back with any developments. :)

by jchadola

Sorry if it sounds confusing but the things that are happening are strange. Yes, if I open IE, 2 identical windows open. With email - outlook express - there are 2 identical emails listed, one following the other.

I wanted to see if my wireless connection worked with my hp laptop - it didn't. So I looked on the website of the manufacturer of the modem/router - 2wire, got a phone number and called them. The tech I talked to was very helpful - I found it very cool that I was in Abbotsford, BC and he was in Arizona and he could take control of my computer - a bit frightening too if that happened when I hadn't agreed. But something happened I don't know if was with my ISP or what - but my router/modem had changed the name of my wireless network to 2wire162 - "162" are the 3 digits at the end of one of the lengthy series of numbers and letters on the bottom of the router/modem. Since I had been successfully using my hp laptop wirelessly for months and now it doesn't work, clearly something happened with the router/modem. The tech guy at 2wire got my connection working on the hp laptop. But now, on my Acer laptop even though it shows my wireless network as being connected, if I click on internet explorer, it says it cannot connect. And I am still getting 2 of everything - I got 2 Internet Explorer screens saying they couldn't connect. And I just clicked once - the 2 screens didn't appear because of what I did. And now I cannot close any screen by clicking on the "x" at the top - I have to open up task manager. I emailed the Operations Manager at Microserve sincce Microserve also services Acer laptops and listed all the rather unusual things my Acer laptop does. Finally I said I'm not using it anymore until it is fixed. The things that are happening are so numerous, it is unuseable. It is so nice to use the hp laptop wirelessly and have it do what it is supposed to do.

But when I said I was getting 2 of everything, that is exactly what happens - 2 windows with one mostly behind the other - 2 emails with one following the other like it was a new email. Yes it is under warranty but I am finding that a lot of the time, the warranties won't cover software problems. I am hoping that Microserve might treat me extra nice since my problem with my LG laptop ended up much higher up the ladder with a not-too-happy Operations Manager about the way I was treated and what they were billing me for. I got an email from LG to whom I must have mentioned what Microserve was not doing and what they were billing me for and it sounds like LG might have contacted Microserve. Microserve wouldn't want to lose all of LG's work. So hopefully I can get Acer fixed at a reasonably justifiable cost. I may not have a ton of knowledge about the workings of computers and I may be a lawyer on long term disability as a result of falling on my face on concrete but I can't stand being screwed around with and that is how I felt. It appears I was being taken advantage of. It looked like they were billing me for one of their staff picking up my LG laptop when the person lived somewhere near me. However, what is really upsetting is that one of the reasons I had my laptop at Microserve was because the card reader would not read my XD card. The operations manager had them order a system board as the card reader was attached to it and the new card reader still would not read the XD card. So now what? I know a separate card reader attached to the LG laptop will read it - but things should work like they are supposed to. So no one has figured out why it can't read the XD card. I'll probably end up getting it back as is and it will never be fixed.

Janice

by jchadola

Thanks - I will do that - I would have liked to have known what it said.

Janicw

by older mycroft

I have usually found one to be enough.

Actually I have usually found something else to spend the cost of the second laptop on - like a monster gaming rig! I can't really judge anyone with three laptops since I'm sitting in the domestic vicinity of three computers myself - I just never imagined having three laptops.

//End of off-topic ramble//

Now, if I'm reading this correctly: the HP is connecting, the LG has a hardware problem and the Acer is currently problematic.

What are the operating systems of these three little beasts?

Since the HP has been the subject of an RDC session, you can safely assume that the internet settings on it are fully operational. Have you tried checking the settings in order to clone the settings onto the Acer?

What computer was connected to the Router when the Tech was fiddling with it remotely?

by jchadola

Yes I do have a stable of laptop - and I also have 2 horses.

The LG has XP on it, the hp has Vista, the Acer has Vista (and - no comments please - the Acer in the box in my living room has XP on it - I got it because for work I needed to connect via VPN and it won't work with Vista and I didn't know if my LG laptop was ever going to work right). I should also say that I am fascinated by computers and I should have gone into that instead of law.

I was using the hp with Vista when I was talking to the 2Wire tech guy.

I am wondering what Microserve and LG are going to do. Even with a new system board (which I assume is the same as a motherboard) that the card reader is attached to, it still can't read an XD card. As the card is readable if you use a separate card reader, there's nothing wrong with the card. Is LG going to force me to keep a laptop that is defective even if it is not a particularly important defect? Or is Microserve going to spent hours trying to fix it as they clearly don't know what to do with it.

Since both the hp and the acer are running Vista, it would make sense to compare the settings - what an awful job though. But I wonder what setting would give me 2 of everything - 2 Internet Explorer windows - 2 identical emails?

Janice

by older mycroft

There are a number of points to cover here:

Let's start with the easiest one first.

#1 "[i]Since both the hp and the acer are running Vista, it would make sense to compare the settings - what an awful job though.[/i]" [b] I don't know where you're getting the idea that it will be an awful job, if anything it may prove to be the quickest of the available options. [/b]All you need to do is access your Network Settings on each laptop, placing them side by side and copy-typing from one screen to the other. The character count for this operation would probably be no higher than 60 characters and a few ticks in the relevant boxes.

#2 In my off-TR Peermails I recalled what I was doing 4 years ago when I had more money than sense. I bought not one, but two of the first-ever Rock Xtreme notebooks, These machines were stunning, right down to the 7 layers of automotive paint that was applied to the chassis panels, then coated in 3 layers of cellulose laquer. They were custom built from the ground up. They were also blisteringly FAST for 2004.

They each had a Pentium 3.2GHz processor at their hearts but the system ran far faster than expected. They also bore a striking similarity to your present difficulties in that they both used to generate twin emails when online.

Now, the first time I invoked Task Manager, the processor graph page featured TWO performance graphs - for what was a system with a single core processor. When I contacted ROCK to discuss this they suggested I keep quiet about the second graph - I deduced this was why the Rock Xtremes were SOooo fast. These little beasts actually were powered by unbadged dual core processors.

The other striking thing about them was that they each both ran with TWO Windows Explorers, TWO Internet Explorers, TWO Windows Shells, and a couple of other instances. As I saw it, the main benefit of all this duplicity in the system was that whenever the computer crashed (even complete with BSOD) the recovery time was almost non-existent. The system would restart in less than ONE second, undoubtedly due to the second shell running in the background!

Which in a lengthy roundabout way brings me to your present problem -

a) what processor is sitting inside this Acer?
b) does your task manger show two graphs?
c) can you sometimes invoke the use of Alt+TAB and it seems like nothing happens?

There is another idea sitting in my head but I want to get this one out of the way first, in case it is a valid one. :)

By the way - BOTH Xtremes were eventually stolen! It never pays to have a laptop that is simply too beautiful to resist!! ;)

My 3-year old Acer is a joy to work with and apparently totally unstealable (and rather ugly!!). :)

This discussion is closed to new replies.