Question Locked

added Ram and Vista will not boot why?

0 helpful
16 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
Added Ram to a Dell laptop and reinstalled Vista. The computer will not boot. Instead it comes up with a count down screan How can I correct this

16 replies

by the scummy one

the proper type for the motherboard?
Is it getting past the POST?
If it is getting into Vista and then failing, it may be a bad memory stick.

by older mycroft

Added ram [b]AND[/b] reinstalled Vista immediately?

A little more detail might help, in as much as:

How much ram DID you have?
How much ram DO you now have?

WHICH laptop are you talking about?

Why did you reinstall Vista - what was the reason?

Can the RAM be seen in the BIOS?

by aron.bury

Also make sure that both sticks are the same speed, and if you can, define what you mean by the 'countdown screen'

by lonniec1143

The Ram was 1 gig, 2 512 chips, Now it has 2 1 gig chips. The screan that comes up is boot in safe mode or boot windows normaly. If I chose boot windows in normal mode it boots, after about 5 attemps. The Ram can be seen in BIOS. The lap top is a Dell

by oh smeg

Have you opened the BIOS and made sure that the RAM is correctly Shown and then Saved the Changes when Exiting BIOS?

There is a RAM Size Change that needs to be saved into the System so that the Hardware correctly Map's the RAM. Just saving the RAM Size Change may be sufficient to cure the current problem but quite often it requires a reinstall of the OS.

Col

by older mycroft

I'm interested in what state the hard drive / operating system was in before all this happened.

by lonniec1143

I am not sure, The user was having problems but I did not talk to the user, My boss asked me to install Vista after he added Ram, And now it wont boot

by older mycroft

It's highly likely that whatever was wrong before - is still wrong now.

It never fails to amaze me how a User can ask for a problem to be fixed (solved) but, out of all the folk involved in 'fixing the problem', the chain of command becomes so lengthy that no-one actually knows what the original problem was.

Let me suggest one possibility:

The User couldn't boot their system due to damage from a virus infection ~ extra RAM was fitted for some reason or other, then the OS was reinstalled by someone else ~ neither of which actions have eradicated the virus. The OS has simply been installed back into a virus-infected HDD and the virus still exists.

You would be better to nuke the HDD before installing the OS, that way you WILL KILL any virus infection once and for all.

http://www.dban.org/download

Run Darik's Boot&Nuke on the HDD, it'll take a few hours at least, THEN install the OS again - this time onto a clean virus-free HDD.

Then before booting, go into the BIOS and [b]SAVE[/b] & exit.

by lonniec1143

Thank you I will try this, and i will save changes in BIOS

by lonniec1143

I am not in front of the computer now, But I did look in BIOS and I did see the Ram was there. It also shows up in system description. That is right clicking my computer and selecting properties

by oh smeg

If you didn't then the Computer is still Mapping the Old amount of RAM and this is where the errors creep in. ;)

Col

by lonniec1143

No I did not save, Bios had seen the Ram, So I did not Save changes, do I need to?

by lonniec1143

What are the correct steps to take when adding Ram to vista?

by jasonhiner

I've had a similar experience where I had to go back in and unseat the cheap and then re-seat it to make sure it is in correctly.

To verify, go into the BIOS after you do this and make sure the hardware recognizes the new amount of RAM.

by oh smeg

As there is a new Configuration for the installed RAM so if you do not save this change the system is stuck believing that there is a different amount of RAM available so it attempts to Map the Old Amount and not the New Amount.

What you should do every time you install new RAM is to open the BIOS check that the correct Amount is shown as being present and then when you exit the BIOS save any Changes this will save the change that you made tot he Hardware by installing the RAM before you opened the BIOS.

Col

This discussion is closed to new replies.