Question Locked

Anyone have any experience with a Medical Program called Genie?

0 helpful
20 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

OK I know I don't do medical normally but this one just sort of crept in on me.

I got a phone call today from a Surgeon who insisted that I fix the problem at his surgery. As he is close to retiring he has allowed one of the Doctors who rent rooms at his Surgery/Patrice to install a 3 Client Network and a Small Server running Windows 2003 Enterprise Server and the Clients are running XP Pro.

The original problem was that the Network was down and they had no access to anything. I unplugged the Switch allowed it to sit for about 30 seconds and then plugged it back in and everything was working on the Network at least though the [b]Medical Program called Genie[/b] was no longer sharing it's DBase. The Server was down so I rebooted it and then started the Program of [b]Genie Server[/b] on it and set about attempting to get the Clients to log in through the [b]Genie Client Application[/b] loaded on the Clients. I found the following Ports blocked 23 & 19813 so I created an Exception in the Windows Firewall [i]at both the Clients & Server[/i] for these ports and promptly got one of the Doctors Clients to log on. Unfortunately none of the other Clients would but I now had one working so I at least thought that I was getting part way there so I repeated setting the Exception to all the Clients and tried again.

Nothing worked though I can Ping the Server or Clients without problems from any Client or the Server and while I know that it's a Software Issue I don't know what to attempt next as I have one Client Working but none of the others and I'm at a loss now.

Of course I tried the Obvious and called the maker only to be told that I've done everything right and the Help Desk Person doesn't know anything about Networking which is helpful.

But as the Software seems to be the immediate problem once I cured the LAN Problem I didn't want to rush headlong into making changes that may be harder to undo if required. After spending 25 minutes talking to the Makers Help Desk I came to the conclusion that I was on my own as while I'm the first to admit that I know nothing about this program I came to the conclusion that I know more that the Help Desk does and this was the first time that I had ever seen this particular piece of software but at least I could run a Ping Command from the CLI and confirm that the problem is no longer in the Hardware but related to the Software.

BTW the Server Logs are showing no errors and I'm currently grasping at straws so if anyone has any ideas I'm all ears.

If any more information is required please ask and I'll post any thing required.

Col

20 replies

by jdclyde

I assume you checked to see if there were any brand new "updates" on the pc's or the server?

Do the clients go over a mapped drive? Telnet? SSH? Webclient? How does it connect?

How about the events on the PC's? I would think you should either see a connection refused at the server end or a connection unavailable at the PC end.

Is the windows "firewall" active? Turn it off to see if you can connect. Always try to simplify the setup until it works, and then secure it.

Check the permissions on the database? If that got changed, it could stop the users from getting in.

Sorry, only know the basics about 03 server or I would mention specifics to look for there.

If resetting the Switch "fixed" the LAN, it might still be your problem. Drop a different switch in to see if it comes up. Is it a managed switch or passive?

by hal 9000

The Connection is by Telnet with no Mapped Drives just a Set Shortcut to the Application DBAse on the server.

Event Logs on the clients show nothing abnormal not even the failed connection.

Problem exists with & without the Windows & Symantec Firewalls turned On or Off. Currently everything is set to OFF. I know it's a Mongrel. :D

According to the Maker the Server Application is right as I've reset everything there or more precisely checked all the settings and all are at the Defaults. I think that they are correct there as the person who setup this mess seems to lack the ability to do anything but set to Defaults.

Server 03 seems to be working OK and I can connect to any Shared Items or whatever across the entire LAN and while I did drop in another Switch it did nothing to improve the problems. Except improve Security. Talk about no security at all. :(

The original Switch is a D Link Router which has the ADSL Modem connected to it to share the Internet connection around the building but currently for now it has a Managed Switch in there which is working OK and I can access anything else except the Medical Program.

I just love Rush Jobs that are dropped on you at 6.00 PM to get ready for the next business day after God only knows what has happened today.

Thanks for all your trouble guys. :x

Col

by gadgetgirl

I don't know it, but can find health people who may...

just a thought - check the db hasn't reverted to the default admin settings on restart - the old system does here, every time..... it'll let you in under the "proper" authorisation, but won't let you *do* anything unless you use the default..... typical NHS wubbish!

Back a.s.a.p!

GG

by hal 9000

This is where I'm at a bit of a loss though as I've never seen this thing previously but according to the maker the Server App is working properly and as I can currently Log on with one Client that seems to imply somehow that it's sort of working right maybe?

I just love Rush Jobs that are dropped on you at 6.00 PM to get ready for the next business day after God only knows what has happened today. :_|

According to the Staff there all that they have done is run NSLookup from the CLI but I'm not holding my breath hoping for anything better like the TRUTH!

Thanks for all your trouble guys. :x

Col

by gadgetgirl

I just talked to a guy who's been in the NHS for years, and is a techie. Apparently, this is a "golden oldie" program that started years ago, and is "most likely" full of bloatware.

Unfortunately, he's only ever seen it run on a Mac system.....??? Dunno if that's where it started out, or if it's a parallel program or what, but he's adamant he's only seen in run on Mac....

I'll keep trying - have 2 techies calling me back.....

Fingers crossed!

GG

by gadgetgirl

From another source - if this program has the e-billing or payment add-on/snap in it may stall as it needs bank info first....

Be careful - the guy I've just had this info from says there are a couple of versions of this program, some from your end of the woods, some from the US, and yet more from Europe - they're all totally different, do different things, have different add-ons etc.

One he's actually seen fall over had to run through an accountancy program called Iris - somehow it was picking up details from there and feeding them into the program for e-billing.....

(Personally, I haven't a clue what he's talking about, I just hope you do, Col - my technical inadeptness is on show bigstyle here!)

Good luck ..........

GG

by hal 9000

There is a FTP Utility in there that is related to this Application which could be the problem as it sends E-Billing away to the HIC [i]Health Insurance Commission.[/i]

So I'll give that one a try first thing tomorrow whoops latter today anyway but as the Dr who uses this application wasn't in that Surgery/Rooms today there will be no E-Billing to do but it's worth a try to see if it improves/changes anything.

Cheers

Col

by hal 9000

I just don't overly believe the Makers who are trying to blame the hardware as all that was wrong is the Switch had been scrambled by a Power Spike over night last night.

If I can speak to the person that the staff where speaking to today at the maker I may have more to work with but currently with a New Strange Application that covers all the Patient Records & Billing I think that I'll remain cautious.

Interesting that this was originally a MAC App and as I've never been silly enough to use it or work Medical Long Term I plead Ignorance.

The last time that I was at this place I spent 4 entire days getting another Medical App to work or at least send the Bills out. :D

Apparently once I decided that the maker didn't know anything about the app I only took 30 minutes to have it working but for some strange reason the Quack wanted to send out bills. I never fully understood that one. :^0

Col

by rob miners

Just been checking the manual and there is a section 4D Tools that will allow you to check the database to see if it needs repairing. The reason that I am looking in this area is because I am familiar with a Paradox DB that was sort of converted to Access and we were constantly running a repair. The site refers to Upgrade CD's as well. This seems to be the latest Genie 7.4.7 30/08/2007 13.9Mb 13.2Mb 7.4.7 Also notice that if you want to part with $125.00 they will send out a Tech to fix it for you.

Another thing to check is that the practice has a current account with the download vendors there is a list on page 56.

http://www.geniesolutions.com.au

Might help Col might not

Rob

by hal 9000

I now have Genie working properly but the Network shares are now nonexistent. And No I don?t know what I did either. :(

Apparently for some reason while the Network Shares on the Server where working yesterday they now once I have got Genie 7.4.2 working are no longer working. Yes I walked out at 6.30PM because I need some Mental Health time as this is ridiculous.

And they are licensed to support 10 Concurrent Connections so it's nothing to do with the Licensing though right now I'm a bit stretched to explain what is happening and even after adding my NB to the LAN and having it work from the same LAN Leads but this computer once reconnected wouldn't.

Now my question [b]Who has a empty Bed in a Mind Dead Ward? I need a Holiday from this nasty work. [/b]

Col

by rob miners

A good stiff drink and place that has a nice comfy chair and a view of the favourite car can do wonders. It helps me. My youngest has just acquired the taste we put a set of extractors on his Hilux last night. Mind you that is why I have the comfy chair and access to the fridge. Nowdays I'm a great supervisor.

by davedxb

Its always like this!

They call you in to check ONE problem when the whole thing is messed up!

And then they blame you! They lie...!

They say it was aaaaaaaaaall working perfectly fine till you came! SO now you fix it or pay the price! BAST******

> : (

Nuke the place.

by hal 9000

I gave to job back to the person responsible for the mess. :D

by hal 9000

I did try very hard to forget all about this one but it didn't work. :(

Apparently the guy who setup the server used some scripts that timed out after a certain number of weeks.

This killed the connectivity between the Server & everything but the main Data Entry Point. Great way of making sure that you have ongoing work I suppose but it's a hard way to go about things.

Col

by rob miners

to see that you got it sorted. Obviously you had to contend with an acute lack of documentation.

by hal 9000

The Software makers Total Lack of Knowledge was a bit of a worry particularly when everyone there insisted that they didn't know anything about Networking. But what I did find interesting was the complete lack of Install Media so I was very careful not to do anything that could cause problems like requiring a Reload. :0

Col ]:)

by martin emanuel

send me a functional copy, and will test for you.

ex subscriber

previously held licence, too far away for current update support

but will look at issue

This discussion is closed to new replies.