Discussion Locked

Assign Letter A: to LS-120 recognized B:

0 helpful
10 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

My LS-120 SuperDisk is recognized as 3? Floppy (B:)Can I change or re-assign the drive letter to A:?
WindowsXP Professional is the installed O/S
which has assigned drive letter B: to the Floppy
Disk. It would seem to me that the LS-120
SuperDiskbeing the only Floppy Disk device
currently installed in this system would be
assigned letter A:? Problems occur in certain
software I use which automatically assumes
A: as the letter assignment for the Floppy Disk.
This problem has proved to be only a minor
annoyance that I currently work around by
using one of several other PC?s I have access
to, many of which I personally built or service.
I have searched a long time for information on
this and made several attempts to resolve it
myself without success. The first one to
provide me with an acceptable answer as to
whether I can or cannot change the letter
assignment will get the points. I have a SOYO
SY-K7V Dragon Plus motherboard with the
LS-120 as primary slave cabled along with a
WD 20GB HDD upon which the O/S is installed.
As not to waste our time here, I have already
attempted many of the basic & obvious solutions
some computer techs might try. Help!

10 replies

by drinkin and thinkin

Is this one of the basic and obvious solutions you've tried?

To change an existing drive letter on a drive, partition, or volume:

Log on as Administrator or as a member of the Administrators group.

Click Start, click Control Panel, and thenclick Performance and Maintenance.

Click Administrative Tools, double-click Computer Management, and then in the left pane, click Disk Management.

Right-click the drive, partition, logical drive, or volume for which you want to assign a driveletter, and then click Change Drive Letter and Paths.

Click Change.

Click Assign the following drive letter (if it is not already selected), click the drive letter that you want to use, and then click OK.

Click Yes when you are prompted toconfirm the drive letter change.

by mmerritt

Yes I did try this. The LS-120 floppy drive B: does not appear in Disk Management at all! I tried this again following your instructions just to be sure, again without success.

by dmiles

The A: drive will be on the end after the twist in the cable and B: drive will be in the middle of the cable. You tell the bios what size drive you have in each place. The drive has no jumper for that purpose.

by mmerritt

As I tried to explain previously in my question, " the LS-120 as primary slave cabled along with a WD 20GB HDD" but should have included "IDE Controller" to avoid any confusion. This internal IDE LS-120 Floppy drive device is not connected
witha floppy cable or to a floppy controller.

by uk_peterg

On startup of your computer, go into the bios settings and make the changes you want here. You may have to enable the option to allow drive letter changes for fdd.

by mmerritt

Please explain. Normally the setting in the bios for fdd is set to disabled when using an LS-120 as the only floppy device in the system and should automatically be assigned drive letter A. I have tried different bios settings for floppy A without success.

by drinkin and thinkin

I ran across this on a message board... I know it's for Win95 but maybe it'll give you a few ideas:

** Go into device manager (control panel, system), go into floppy controller and then tick 'disable this device'.
Remove the LS120 device from device manager, reboot the system, Win 95 should then pick up the LS120 and put it on A:.
If it doesn't, remove the floppy controller entirely and make sure you install the LS120 before the floppy when it asks you.**

The reply was: (paraphrased)
** Worked but I also had to set the drive A: in the BIOS to none.**

Good luck.

by mmerritt

While not the correct answer (see my comments) you made me re-think this thing and solve it myself very quickly! Much Thanks! You get an A:)for effort and the 300 points.

by mmerritt

After spending hours attempting to find a solution to resolve this, my LS-120 is now recognized by WinXP Pro as 3? Floppy (A:). I searched the Windows Registry for B: and modified two lines of several instances found.Entries for installed from B: were replaced with A: in
addition to removing a line relating to drive B: from a list of all drive letter assignments. I removed the LS-120 Floppy Drive from Windows Device Manager then shut down my System for the evening. BIOS settings for floppy drives have
always been set to none and FDC disabled. Today when I powered up the system I was pleasantly surprised to find floppy A: instead of B:! I wish to thank everyone for their input, none of which provided the specific answer I needed however, gave me new ideas and made me think!

This discussion is closed to new replies.