Discussion Locked

Automotive Engineering at it's best (not)

0 helpful
8 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

http://money.cnn.com/2012/06/22/autos/chevrolet-cruze-recall/index.htm?hpt=hp_t2

Read the second paragraph of this article about Chevy Cruze recall:

"The engine shield, a large plastic piece that is installed under the front of the car to protect the engine, could trap oil that is accidentally spilled or dripped during oil changes."

"Also, in cars with manual transmissions, driving with a worn clutch can cause burning hydraulic fluid to squirt from the clutch housing. The flaming fluid can ignite the engine shield leading to an engine compartment fire."

Who knew that a worn clutch causes flaming fluid to be ejected from the transmission! I would pay to see that. That must be a Chevy thing! :)

From GM press release:

"In Cruzes with manual transmissions, continuing to drive with a completely worn clutch may cause hydraulic fluid to be expelled from the clutch housing vent hole. Under certain circumstances, the fluid could be burning as it exits the vent hole. If it contacts the engine shield, the shield may ignite and a fire may spread to the engine compartment."

8 replies

by hal 9000

[i]a large plastic piece that is installed under the front of the car to protect the engine[/i]

Sounds as if they are describing a Sump Guard but making them of plastic isn't really an option let alone making it in such a way that it could collect oil or other fluids.

The Clutch issue seems like a Perfect Bean Counter Job to me where the worn clutch plate causes the pressure plate to lower causing the Slave Cylinder to need to move the piston further in the bore and tilting and allowing the fluid to squirt out when the clutch peddle is pushed or worse still actually exiting the bore.

Both are extremely Poor Design but most likely both where approved by Government Safety Agencies who have lots of Pen Pushing Bureaucrats and no one with any common sense or actual Design Experience.

After all how can you make any plastic strong enough to be a Sump Guard without Webbing which traps spills/leaks. Yes I know it could be Carbon Fiber which is certainly strong enough but then again Carbon Fiber has very poor scuffing characteristics which makes it unsuitable for such a job. After all what's the point of having something solid enough to protect the sump if it disappears when it's rubbed along the ground?

The Clutch Issue is a completely different story and I did notice that there is no listed fix for that. Even replacing the Clutch Plate and so on will not prevent it from happening again when the Clutch Plate wears or the Pressure Plate looses Tension. They need to fit a new Slave Cylinder which is longer. :D

Col

by robo_dev

The shield is typically held in place little plastic clips which get lost/broken over time.

It's purely for aerodynamics and to more or less deflect mass quantities of rain/snow/insects/dirt from building up in the guts of the engine bay.

The point that I find funny is how the press release seems to mention casually what would be a really BAD thing...e.g. flame shooting from the clutch housing.

" worn clutch may cause hydraulic fluid to be expelled from the clutch housing vent hole. Under certain circumstances, the fluid could be burning as it exits the vent hole."

So we're talking burning fluid spraying out of a vent hole...seems like no big deal, just a little flamethrower going under the car, nothing to see here :)

by hal 9000

They mess up everything that they touch.

At least with the 1 car I was involved in the design of we told the Marketeers that they could change whatever they liked provided that nothing was changed other than the paint work.

We also allowed them to change the color of the wiper blades but not the arms. ;)

Luckily that was never designed to be a Mass Production Car just a Limited Production Car which was sold out before it hit the Order Books. :D

Col

by hal 9000

It's a way to improve heating and to help melt the snow traveling under the vehicle.

Add that to the Modern Plastic Fuel Tanks and thin Hydraulic Lines and it's way to sell new cars and Funerals. ;)

Col

This discussion is closed to new replies.