Discussion Locked

Blank Screen after adding RAM?

0 helpful
10 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I have a Dell Dimension 4500 and recently tried to add some RAM to my computer. I did a really stupid thing and turned off the PC but didn't unplug it before I popped it open and put it in. After the ram was in, I turned the computer back on and it recognized the memory, but then the monitor started to blink and go to black, then be fine, then black until finally, it just stayed black.

Now when I turn it on, the computer powers up in that the fan and lights come on, but I nothing shows up on my monitor and the light on the monitor itself blinks green.

Did i fry my computer? Graphics card? Motherboard? Does anyone have any suggestions?

10 replies

by simy

Maybe the problem is the RAM itself. Take the new RAM out and so that it is in it's original configuration. If it boots properly, then the problem is with the new RAM.

Hope this helps

by hal 9000

Are you hearing any Beeps from the Case?

If so you most likely have a timing issue with the different RAM so it's not working or even playing nice with each other. Remove the new RAM and try to boot with only the original RAM installed if this works shut down pull out that RAM fit the new RAM and reboot. If you get a picture with bot sets of RAM you have a timing issue between the two sets. If it doesn't work at all with then new RAM they most likely it is the wrong speed and has a timing issue with the M'Board/CPU.

If you can not get a picture on the monitor at all then pull the Video Card and re seat it, it may have been slightly dislodged when you fitted the RAM and is no longer making a proper connection.

Lets know how you get on.

Col

by hal 9000

Also check the monitor plug to make sure that it hasn't become dislodged as what you are describing is a working monitor that isn't getting a signal to work off.

by rickrbyrne

Do you have an intergraded graphics card or AGP/PCI/ PCI-x. A bad stick of RAM will affect your display if you have an intergraded card because the system RAM is being used as your Video RAM as well. So if you can take out a stick or replace the RAM with your old RAM and see if you get a display.

by freetechie

If it beeps at all check your manual for beep configuration error sounds. That is your best bet.

1) Turn off everything and open the case up
2) Install OLD ram for testing
3) Close everything up and plug in
4) Turn on to see if it works
a) It will turn on
b) It won't turn on

If A
1) Turn off everything and unplug power (not really needed but precautionary)
2) Open case and take out old ram
3) Install One module in slot and make sure it's seated properly
4) Close eveything up and turn on
5) If it works you are golden if not try a different slot and make sure its seated properly and try different modules
6) If this fails it's the ram you bought

If B
1) Check your video card to be seated properly
2) Check you video card cable
3) Check CPU seated properly, and heatsink is attached properly
4) Put old ram in
5) Close case up and plug in power cord
6) Turn on
c) If it does not turn on try to change your video card
d) try to change you cpu

by dmiles

The ram is problaly conflicting by not being the same or incompatible with the new memory.
Check by adding the new ran withoutold ram and see if this works,you want to have the same memory modules in the system

by synthetic

Keeping the system plugged in was possibly a good thing, as it provides a ground for any static charge you may be carrying, so take that out of the equation. The most likely cause is the new RAM, while compatible with your system, runs at a different clock speed than the current RAM. Another possibility, is that the memory matrix is not being satisfied. Take a look at the manufactures web site to verify you can add a 64 DIMM with a 256 DIMM (or whatever memory size you added).

by jrice

Turning the power off and pulling the plug is the best way to change RAM. It is possible to damage the motherboard and or ram. Pull the new RAM and Boot UP. If it works your cool. Sometimes some RAM chips will not work with the Dell computer

This discussion is closed to new replies.