Discussion Locked

Boot issues

0 helpful
17 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
I am working on a dell laptop that will only boot to a dos prompt (c:) It will not continue the boot process.What can I do to get it to boot all the way?

17 replies

by syscokid

I assume you're using Win 9x. If so, go to Windows Explorer, click on View, Options, and make sure Show all Files is checked. Then in the root directory, find msdos.sys, right-click it, go to properties, and uncheck read only. Then open the file with Notepad, and make sure there's a line that reads Boot Gui=1. Save the file, make it read only again, and restart the computer.

by syscokid

OK, how stupid can I be! You can't use Windows Explorer so you can't do what I suggested.

Do what Chipmunk said, type win at the prompt and press enter. If this starts up Windows for you, THEN do what I said to fix the problem permanently.

If Windows doesn't start, then I agree with the suggestion to reinstall.

by chipmunk

If you have Windows 9x. When you get to C:\ type in win then hit enter, if that don't work, then I recommend to reinstall Windows 9x. This should keep all your settings the way it was, just be sure that you install it into the same Windows fold, example: default is C:\Windows. That should bring you back to where you were.
Alvin

by tbradley

When you get to the C:\ prompt

type in "ver" without the " " and hit enter

the screen will show you what operating system is loaded. If win 95, or win 98,
type in "dir" without the " " and hit enter

if you see a directory {windows} with brackets, type in path=c:\windows\command

at the c:\prompt, type in edit c:\msdos.sys

change the bootgui to =1

save the file, and re-boot.

If you don't see win95/98, or there are no windows directories on your c: drive, then you have no choice but to reload.

good luck

by jnicks

There is one other thing you can do to get yourself booted into windows if you are using windows 9x. At your C:\ prompt, type the following commands.

ren autoexec.bat autoexec.old
ren config.sys config.old

That will rename your Autoexec.bat and Config.sys files. Neither of these files are required to boot into windows, but they can contain entries which prevent it. This usually occurs after loading legacy software or hardware, but not always. If you have any important drivers loadingin those lines, you'll want to consult your manuals and perhaps reinstall those to get new, cleaner config.sys and autoexec.bat files.

by jnicks

Oh yeah, you can also try typing exit and hitting enter. That sometimes does it too.

by tuqan

While at the DOS prompt type "Dir /a /p" without quotes of course. The first switch grants you access to all files in that directory including those that are attributed as being Hidden which the MSDOS.SYS file is and the other switch is to pause the screen allowing you time in which to see everything before it whizzes by. Having found it now you must alter its file attribute which is READ-ONLY and I believe SYSTEM as well before you can successfully edit the file. To accomplish this type thecommand "ATTRIB MSDOS.SYS -s -r". After this you merely type in the command "EDIT MSDOS.SYS" which should then bring you to the Qbasic editor. Now that you are into the MSDOS.SYS file check for the Bootgui line and make sure it is "=1". You can save the file, exit and try rebooting at this time or if you would like to get rid of the Windows Splash screen altogether now is a good time to do it. To accomplish this add the line "Logo=0". This will enable you to see some of the commands that are being executed behind the scene so-to-speak as Windows is starting. If you want your beloved Windows Screen back just re-edit the file and remove the line. Oh, and don't forget to ATTRIB the file back to it's original status when you are done with it....Good Luck

by george.lostia

have you tried booting to safe mode. to do this you will need to hit F8 just as the starting windows message appears in the uper left corner then you should be able to view the files mentioned earlier

by bww5195

I have seen this twice.

Check the CONFIG.SYS for a line that says:
DOS=SINGLE

Rem out the line and reboot. Other than that I agree with the guy that said to rename the AUTOEXEC.BAT and CONFIG.SYS to see if it is either of those causing theproblem.

(When I saw this, the impatient user had double-double clicked a shortcut to a dos app. That supposedly caused the o\s to add the line mentioned above to the CONFIG.SYS. I've tried to duplicated the double-double click to reproduce theproblem but was unsucessful. The DOS=SINGLE line does cause the same thing that you are experiencing though.)

This discussion is closed to new replies.