Discussion Locked

boot up lag

0 helpful
21 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I have been working on a system that is running Win98SE that takes 45 secs from the time it brings up the bios settings to display the harddrive type and then another 40 secs to start Win98SE. The system is a local build and has a Soyo SY-5EMA+v1.1 Mobo with an AMD-K62 500 Socket 7 proc with award bios v1.0A 4.51pg.
I have tried the following just to be sure: Bios flash, cmos edit(several times), renamed autoexec.bat and config.sys(even though I believe it is hanging before these ever start),deleted programs that I thought might have impacts, checked startup, edited msdos.sys to stop dblspace & drvspace from starting, etc, etc, etc....
I could use some real smarts about now before I throw this pc back at the user and tell 'em where it should be put.
Thanks,

21 replies

by ndellasala

it is the amd-k62 processor. Either replace with a newer model or have the user deal with it

by dw-nav

Tried that already. It's a new proc but I replaced it with one that was working fine on another system. Please, try again.

by juguzman

I encountered the same problem a while back with a Windows 95 machine. I did most of the things you have described above and nothing worked. What finally did work was removing software that had been installed, removing most previously installed software first.

by dw-nav

I have already removed all the software one by one until I got tired of re-booting to find out which one it was and re-formatted the HD and re-installed a clean Win98. Sorry, still hangs at the same place.

by david balogh

it cant be the software installed (unless you have installed something that would affect the hardware directly) so its in bios, you said it takes time for the harddrive to be detected, it sounds like you have not put a proper configuration into bios, do NOT just leave it on auto detect. Go into bios and do a detect, or put the paremetres in yourself, this will save the bios from looking for the drive each time and know exactly what its looking for.

by dw-nav

Good thought! After checking the bios against another identical system I found that there had been a flash on the system in question. I found the bios flash disc and found the original flash was copied to the disc. I re-installed the original bios. Reset the default values and set the drives to user and set parameters. Bad news - still hangs at where the drives would normally be detected. (I actually thought this would be the resolution)

by jasonbis

Just a thought. You may have a worm which would cause your system to slow way down during boot up and everywhere else. Go to start, find, files or folders and do a search for hta files. Type in the box *.hta and hit enter. If you find anything delete it and then go into my computer and right click the c: drive and click properties. Click disk cleanup and delete all your temporary files.

by pault

If the HD is on the same cable as the CDrom, try removing the Cdrom drive from it and see if that helps. I had trouble with A Soyo board, IF (DMA)was enabled for the Cdrom while sharing a cable. Good luck.

by dw-nav

When I took the cover off I made sure the HD & CD-ROM are on seperate IDEs. You know this is getting rather personal now. At first I thought I was going to give up on this pc but now I'm PO'd and don't want to give up. Keep 'em coming! Someone is bound to have the answer. Thanks, for everyone's input so far. There has been some good advice - too bad it hasn't worked. :)

by nteldata

Work backwards and start with nothing connected to the mothermoard but power, your video card and the keyboard.
Configure the BIOS with its default settings, and restart the computer and see how long it takes to get the message that there are no bootable devices.

Q. Is it under 30 seconds?

A. No- then try swapping the CPU, Memory and recheck all the MB jumpers. Change the BIOS settings and start disabling devices, set every ?Auto? setting to ?None? or ?Disable?. Recheck the startup speed and see if it any changes have made a difference.
Check and see if the BIOS has an internal diagnostic setting that can be disabled.

A. Yes- then go forward and start connecting one device at a time, try the diskette drive, then the hard disk drive, then the CD-ROM and then other cards that plug into the MB.

You may find that one of the devices is causing the problem. If not swap-out the system board.

by dw-nav

Bob, I worked backwards and when I removed the sound card the hang up went away. I would never have guessed this. THANKS, for the help of everyone who gave me a response. I appreciate it and saw some things I wouldn't have thought of. Stored forfuture reference.
THANKS AGAIN!!

by jctech

I know this might sound too simple, but sometimes the most simple solutions are the ones most overlooked. You might want to check and make sure that the jumpers on the HD are set properly. If it is the only drive connected to the controller, make sure it is set as a single drive rather than a master. On some systems, setting a single as a master works just fine, but on others, the system gets confused and takes forever to boot, if it is able to detect the drive at all. This may not be the cause in this case, but worth considering.

by ins413

Just a thought, but why not try setting the cmos hard drive settings to manual. It sounds like it may be set to auto detect. If you set it manually it may improve boot time.

by mmetrick

I've seen this caused by the system looking for an IP address. If you have set any network settings, see if you can change the IP setting to a defined value, instead of "obtain IP address automatically" If the system was set to auto, it times out while searching for an IP addr. Hope this helps.

This discussion is closed to new replies.