Question Locked

booting

0 helpful
9 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
I just restarted my PC and I hear a 3 long beep after there is nothing coming on the screen the light on the monitor flashes on continously. please what the fault?

9 replies

by toivo talikka

You have already done troubleshooting and there are not too many options left. Did you put the hard drive back to your computer after finishing the installation on a different computer, and what happened?

by tg2

CDRom drive would be a possibility also.

Set your bios settings to defaults (don't try to tweak settings, if possible save the current bios state)

If you tweak after the installation sometimes the system deals with the changes, but during install it may not.

by ericus882

When I put back the hard drive and switch on the computer after the boot it says NTLDR is missing. press any key to restart.

by jamesatmaisonverre

RESOLUTION
To troubleshoot this issue, follow these steps.

Warning Do not complete the following procedure unless you are very familiar with internal computer hardware removal and installation. The hardware components in a computer are very sensitive to static electricity. For information about the correct handling of computer components, contact your computer manufacturer. 1. Shut down your computer, and then remove all the Peripheral Component Interconnect (PCI) devices.
2. Restart your computer.? If Windows starts successfully, shut down your computer, and then reinstall the PCI devices one at a time. Start Windows after the installation of each device. When you install a device that causes the issue that is described in the "Symptoms" section, remove that device, and then continue to install the other PCI devices.
? If Windows does not start successfully, remove one or more of the memory modules that are installed in your computer. Leave sufficient RAM for your computer to start and run Windows XP.

Note Windows XP requires 128 megabytes (MB) RAM. The minimum is 64 MB and the maximum is 4 gigabytes (GB).

For example, if two 256-MB memory modules are installed in your computer, remove one of the memory modules. If Windows starts successfully, shut down the computer, and then reinstall the RAM modules one at a time. Start Windows after the installation of each RAM module. When you install a module that causes the issue that is described in the "Symptoms" section, remove that module, and then continue to install the other RAM modules.

3. Determine if the PCI devices in your computer are compatible with Windows XP. To do this, visit the following Microsoft Hardware Compatibility List (HCL) Web site:

by ericus882

When attempting to install a fresh copy of windows XP on my computer it says THE file usbehci.sys is currupted and even I put windows 2000 it says the file dmio.sys is currupted press any key to continue.
pls advice me.

by getanswers

? When you start your computer by using the Windows XP Recovery Console or by starting from the Windows XP CD-ROM, you receive one of the following error messages:
Setupdd.sys could not be loaded. Error code 4.
Setupdd.sys could not be loaded. Error code 7.

Back to the top

CAUSE
This issue may occur if your computer contains a hardware component that is either damaged or is incompatible with Windows XP.
Back to the top

RESOLUTION
To troubleshoot this issue, follow these steps.

Warning Do not complete the following procedure unless you are very familiar with internal computer hardware removal and installation. The hardware components in a computer are very sensitive to static electricity. For information about the correct handling of computer components, contact your computer manufacturer. 1. Shut down your computer, and then remove all the Peripheral Component Interconnect (PCI) devices.
2. Restart your computer.? If Windows starts successfully, shut down your computer, and then reinstall the PCI devices one at a time. Start Windows after the installation of each device. When you install a device that causes the issue that is described in the "Symptoms" section, remove that device, and then continue to install the other PCI devices.
? If Windows does not start successfully, remove one or more of the memory modules that are installed in your computer. Leave sufficient RAM for your computer to start and run Windows XP.

Note Windows XP requires 128 megabytes (MB) RAM. The minimum is 64 MB and the maximum is 4 gigabytes (GB).

For example, if two 256-MB memory modules are installed in your computer, remove one of the memory modules. If Windows starts successfully, shut down the computer, and then reinstall the RAM modules one at a time. Start Windows after the installation of each RAM module. When you install a module that causes the issue that is described in the "Symptoms" section, remove that module, and then continue to install the other RAM modules.

3. Determine if the PCI devices in your computer are compatible with Windows XP. To do this, visit the following Microsoft Hardware Compatibility List (HCL) Web site:

by meetrahil

This issue may occur if your computer contains a hardware component that is either damaged or is incompatible with Windows XP.
1. Shut down your computer, and then remove all the Peripheral Component Interconnect (PCI) devices.
2. Restart your computer.? If Windows starts successfully, shut down your computer, and then reinstall the PCI devices one at a time. Start Windows after the installation of each device. When you install a device that causes the issue that is described in the "Symptoms" section, remove that device, and then continue to install the other PCI devices.
? If Windows does not start successfully, remove one or more of the memory modules that are installed in your computer. Leave sufficient RAM for your computer to start and run Windows XP.

Note Windows XP requires 128 megabytes (MB) RAM. The minimum is 64 MB and the maximum is 4 gigabytes (GB).

For example, if two 256-MB memory modules are installed in your computer, remove one of the memory modules. If Windows starts successfully, shut down the computer, and then reinstall the RAM modules one at a time. Start Windows after the installation of each RAM module. When you install a module that causes the issue that is described in the "Symptoms" section, remove that module, and then continue to install the other RAM modules.

3. Determine if the PCI devices in your computer are compatible with Windows XP. To do this, visit the following Microsoft Hardware Compatibility List (HCL) Web site:
http://www.microsoft.com/hwdq/hcl (http://www.microsoft.com/hwdq/hcl)

This discussion is closed to new replies.