Discussion Locked

Cable Modem Network

0 helpful
19 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Hi

I like to have information on cable modem network. Is there anyone can help me to know about that. If yes please send me the details of the cable network design. What sort of equipmetn do I need for cable modem network. Can also send email to paulsumon@yahoo.com.

Thanks and regards

Paul

19 replies

by mckaytech

The key piece of equipment you will need is a "head-end" switch. There are a few manufacturers of these but one information source I can point you to is ADC's Web site.

If you go to www.adc.com and search for 'cable systems', you'll find information on their Cuda 12000 IP Access switch which is one such device.

paul

by rachel_s

It will depend on your cable modem provider. I use MediaOne resently bought by comcast. At first I used a firewall/proxy server setup, which was ok, done on a Pentium 133/64MB RAM.
A family member was getting cable modem service, so I recommendeda switch/router setup for less than $150. A friend of mine recommended Linksys, so I purchased it for them.
I tried it out at home, and liked it so much bought one for the home, much faster, not as secure as a firewall, but it does NAT and DHCP.
The WAN port also does DHCP (only had to tell the ISP the MAC address of the WAN port) and we are ready to go. There are other settings that can be used for web servers and such (NAT), but I don't use them, so I can't tell you how those work.
If your looking for a simple and inexpensive setup - I highly recommend it.
And you can configure the thing with a web browser, and I believe mine came with a free CD of turbo linux :*) Plus I have bragging rights to a switched network at home!

by ryder007

Hi Paul, Here are the essentials, First get your cable provider to set you up with a cable modem, next purchase a router and a NIC card for each remaining machine you want on the network and cat5 patch cables for each machine. Run your Cable modem into the router and the Cat5 cable back out to each Comp. Then all that is left is to set your comps up as a network and make sure each comp. is using dhcp and you should be set.You can purchase all of the stuff you need at a bestbuy or comp usa or any other comp store neer you.

Dean

by fossil

This USED TO be as simple as ryder007 describes, and still might be in some areas. However, cable providers really don't like line sharing and often want to charge for additional machines at the same location. Even if ryder007's method works for you today, in the near future, it probably will not. The method rachel s describes will work today and longer into the future. Don't cheap out. The method rachel s describes will cost more, but will last longer. When you purchase the equipment, look for "DOCIS 2.0" compatitiblity in the documentation. It's the newer standard that cable providers are moving to and will help assure the longevity of your equipment. Also, calling your cable provider and being up front and honest is likely to result in additional charges because, most likel;y, the rules of your cable agreement probably define what you (and many many others) are attempting to do as theft of service -- but who doesn't hate the cable company?

by briantruitt

Yeah, save yourself $150 dollars by just installing 2 nics on one pc. Connect the cable modem to the pc with 2 nics. One nic for the cable modem and one for a hub/switch. You can either use ICS or NAT (or dhcp and dns if you have a large network)depending on the OS. You cannot plug a cable modem into any old hub. You need some sort of dhcp proxy or something. Any cable provider will tell you that in order to network your home you need an ip address for each computer in the house. You can just use a plain old hub if you go that route but why pay the extra money for ip addresses when you can make your own. The cable/dsl routers are cool but out of my budget. I spent $15 dollars on another nic and have the same setup as those guys plus I control everything with my W2K Server machine.

by kmerrillt

I run a home network with 3 PCs using cable access for the internet. This is a simple process, which usually isn't depicted that way. You will want to use a 4 port ROUTER so that you won't have to worry about paying extra for sharing your cable access. Routers for home use are very inexpensive (under $100.00) and very easy to setup and use. If you e-mail me with your current hardware and Operating systems I can give you complete instructions.

by rileylk

Answer #5 is right on the money, AND you don't even need Win2KPro, Windows 98 2nd edition will do. You add a second Nic to the Windows machine. Plug your cable modem into the first NIC, and plug a hub or switch into the second nic. Then run the Internet connection sharing wizard and it will guide you through the setup. Plug all additional computers into the hub and set them to obtain addresses automatically. All of the details are in the Win98 help file. The entire process is surprisinglyeasy. Good luck!

by paul

Hi all
Thanks for replying my question.
The meaning of my question is, I like to know how Internet service provider is distributing internet connectivity through cable modem. The network design of that connection. From ISP to user end.

Thanks

by estebandelatorre

It's all depends on what hardware is your cable company using.
The best research would be web pages of possible cable modem providers at your zone.
As a general definition, they arrive at your house with a coax cable, to a box. In order to connectyour box to your pc, you will need to install a network card into your pc, and attach both devices with a cross upt cable.
The box performs a NAT translation which make it a "proxy like" kind of access (without a cache).
Good luck

This discussion is closed to new replies.