Question Locked

can not communicate with printer!!!

0 helpful
8 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I have two epson stylus pro 7500 large format printers, one works fine but the other will not communicate with the computer ,,i pressume its not the leads or drivers as i use the same computer and the same leads when opperating both printers! can any help me find the problem i think it may be a setting on the printer itself but im not sure!

it was all working fine then one day last week the error come up on my computer "error communicating with printer"

if i print a test sheet using the display on the printer it works fine and the test sheet is accurrate! this would indicate that all is good with the basic printing and motherboard functions, but im unable to send any work to the printer from the computer and it also fails to communicate when i try to use the status monitor in the epson printer properties, anyone know about this error? please help!!:~)

8 replies

by older mycroft

I suggest you physically swap the printers.

If the fault occurs again, after the swap, the problem lies with the cable / physical connection.

Try that first.

by jjrichards.dps

my other printer works fine using the same usb cable, and the same computer and they have worked using the same equipment and drivers for good 12 months, i have swopped and changed everthing to do with drivers, usb cables and even tryed both printers on a laptop.

same as before same printer works and same printer will not communicate, im pretty sure its safe to say the fault is on the printer not the other bits, i do know i have to set the ports on the computer but maybe there is a way to set the ports on the printer as it does have a bios,processor and motherboard much like a computer! thought it could be some sort of curruption within windows if its not the printer?
does anyone know when using two of the same printers on one computer(not at the same time)should they react in the same way when swopped? not sure about any of it really!! :) it has a parrallel port so im going to buy a cable tomorrow and try that, anyone know of other reasons why it would do this feel free to pass it on!!

thanks in advance :)

by hal 9000

Open it up and look for some loose or broken parts floating around in the bottom of the printer. I think you'll find that something has fallen into it and caused it to break.

You can try turning it on without being plugged into a computer and see if it initializes correctly IE moves the print head/s.

You might find something useful here but I think that the you'll find that you have a mechanical problem in the printer and that it's cheaper to replace than repair

http://preview.tinyurl.com/2mjqar

Col

by jjrichards.dps

but not when plugged into the computer!

i have printed all the test prints from the printer console when not plugged into the computer , it is printing the tests fine! nothing wrong with mechanics or the print heads, as all the test prints are good, this would say to me that its a problem with the usb port on the printer or even a software issue within the printer itsself!

anyways the diagnostic printout says there is nothing wrong but as it will not communicate with comp there is something wrong!

anyone know why everything would work within the printer when standing alone but can not receiveing info from comp? please help :)

to replace this printer will cost me ?3000 as its a large format so a new one is out of the question at the moment!! i do have another the same but i need both running!!

thanks again to those who replyed........ :)

by hal 9000

Not just the USB Interface as it's just one small part of the printer. As you can print the test pages which are Hard Coded into the unit all that means is that the print heads work correctly but what is getting to them can be a different story. It could be something as simple as some junk stuck in the USB Socket have you actually looked to see what if anything is in there and if the socket looks all right? Compare this to the working printer as a base version of what it should look like.

Now as the USB Port is on a Circuit Board it could have failed that's the Circuit Board or the USB Socket could have been ripped off the Circuit Board. The units RAM could have failed so that when you send it a print job it is unable to interpret the print job and throws up rubbish if it works at all.

If you can not see anything obvious and as the Test Pages Print OK your only option them is to take it to a Epson Repairer, you may find this Web Page of use

http://preview.tinyurl.com/yvkbcv

And allow one of the authorized repairers repair the unit but at the very least ask for a Guesstimate before allowing them to repair the unit as from past experience the Internal Parts are very expensive and on one Epson just the Power Board costs more than a complete new printer and this wasn't on a $75.00 bottom of the range but a Top of the Range Photo Printer.

The large format printers which are effectively A3 printers are of smaller sales volume so they cost more as there are not as many made and the parts are equally expensive again because of the lack of Scale of Production. If they don't make as many of one model that is expensive the parts and Service costs will be increased because of the costs involved in storing parts that the company By Law is required to carry. Or they could do a HP and Bin any product that breaks while Under Guarantee and simply replace the broken unit with a new one. That to would meet their requirements to sell product that s serviceable. Of course a problem arises when the units are no longer UG as by then all bets are off and you are at their mercy as they can charge whatever price that they like for parts.

Anyway the bottom line is if you are unable to see something obvious you should take it to an Authorized Repair Station but do not be surprised if it's cheaper or just under the cost of a replacement unit to repair. I look at these things from a purely economic prospective if they cost more than 50% of the purchase price to repair after 4 to 5 years then they are not worth repairing as you are only replacing a very small part of the complete system and the other bits could just as easily fail and then with the second repair you will have paid more in repairs than buying a new printer with a Warranty and still have the possibility of more parts failing that is going to cost you even more to keep this unit running and by this stage because of the money you have already spent on repairs you are locked into keeping a failing unit running. Then there is no guarantee that it will keep running and after 3 or 4 break downs you can quite easily find that you have paid for a new unit a few times over and still not have a reliable working unit that you can rely upon.

To put things simply these really are Throw Away Items when they break unless there was a design flaw that resulted in a Product Recall then the Maker will repair the unit at no cost to you.

Col

by bogdan.botezatu

Try it on another computer and see if it works. If so, then the problem resides somewhere in your first computer. As the cables are ok (you said that you replaced the cable with the other printer's), it's only a OS malfunction somewhere. Try re-installing both printers, in order to clear the Printer Spool folder. The worst case scenario includes a reinstall of your OS.

by jjrichards.dps

so this is what i did, even though i had tried it on laptop yesterday which give the same result! i went arround to my brothers place and stole his comp while hes at work!!

set it up , installed drivers from epson, and to my supprise the bloody thing works!!

as happy as i am this still gives me further problems!

how do i get it to work of my work comp? is there a problem with my op system or would it be the drivers conflicting?

why does one work on my comp but the other not?

HAL 9000--your post was very informative and thanks for taking the time to reply, many just read and move on!!

BOGDAN-- even though i had already tried it on my laptop as well as the work comp your post propted me to get my brothers comp,

i even put the darn thing on ebay last night for spares or repair, got a bid as well :)

have pulled it now though but i think i will put it back on for sale as working afer reading hal 9000 post , 6 years old now these printers so time to upgrade i thinks!! dont want any ?3000 repair bills in the future, should get about ?1600 for both printers on ebay so only have to put ?1400 to get a brand new 9000 series....

thanks again to all those who replyed

John :)

This discussion is closed to new replies.