Question Locked

Canon Bj 4300 printing only line not text

0 helpful
17 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I'm in dire straights here. Any help would be greatly appreciated. I have a Canon bjc 4300 printer the printer is printing small blocks og colored lines--and that's it. From any document it will only print these horizontal lines. I'm using windows XP- I have uninstalled the driver and reinstalled with no errors.
I really need to get this fixed as i have reports due. (Pulling my hair out)

Thank you so much for any help in advance

17 replies

by oh smeg

The printer is locked in some form of Test Mode.

Try opening the Maintains Tab of the Printer in the Printers & Fax Window and see if you can clear it from there.

Failing that you may be required to read the User Manual to see how to unlock the printer. Or try these Instructions

[b]Canon BJC-210, BJC-240, BJC-250, BJC-255, BJC-265
Canon BJC-4100, BJC-4200, BJC-4300, BJC-4400, BJC-4550, BJC-4650
1. Unplug Power Cord
2. Hold POWER and RESUME buttons
3. Plug in Power Cord
4. Release buttons
5. Open front door of printer
6. Hold the CARTRIDGE and RESUME buttons
7. Press POWER
8. Release all buttons after the beeps
9. Press CARTRIDGE once
10. Press RESUME[/b]

Col

by bean2473

Thank you so much for trying to help me- it's still printing just lines-even on the test page it's just black and colored line..Is this fixable?

by older mycroft

By that I mean, you said [i]"it's still printing just lines-even on the test page it's just black and colored line."[/i]

So does that mean that you can invoke a Test Page print (as opposed to trying to print a document) from the Canon control screen?

If the coloured lines are printing in Primary mode (Yellow, Magenta, Cyan, + Kohl) - [b] is one of the colours missing?[/b]

Canon used to have a 'telltale' system that would invoke the sort of output you are getting, if one (or more) of the ink units had become dislodged. The colour that was missing being the 'telltale' indicator.

Try removing all the cartridges en masse, then reinserting them CAREFULLY. ;)

by bean2473

Ok here is the break down- if I try to print regular text, say from note bad it prints colored blocks-all the colors it prints one on each side of the top of the page and one on the bottom middle. When I try to print the demo page from the software it prints what looks like the text pattern but instead of text it's printing a yellow line then a red line and the rest is a big black box with all the colors mixed in.

Thank you to those who are helping me you're lifesavers!

by bean2473

both ink cartridges are new. I cleaned to print head as well. Also, I tried a different bjc 4300 driver (windows xp driver) and that driver caused the printer to not print at all, it would act like it was printing but nothing appeared on the paper, so I switched it back. I figured colored blocks were better than nothing.

by older mycroft

But I thought you were looking for a solution.

Ah well, you obviously know best. ;)

by older mycroft

Y'see "[b][i]No blue line but...[/b]
both ink cartridges are new[/i]."

Doesn't suggest to me that you removed the cartridges and reset them again. I can only go by what you tell me, I'm not psychic.

However, if as you say you "[i]tried a different bjc 4300 driver (windows xp driver) and that driver caused the printer to not print at all, it would act like it was printing but nothing appeared on the paper, so I switched it back.[/i]" - I thought you had a Windows XP system ? So which printer driver did you switch [b]BACK[/b] to then, if it's not the XP driver ???

by bean2473

I switched it back to the original canon driver.
Please,I'm not trying to make enemies here i'm just trying to get some badly needed help. So, with that being said I am following everyone's directions to try to fix this printer.

by older mycroft

[i]"I switched it back to the original canon driver."[/i]

[b]HOW did you accomplish this ??[/b]
If you rolled back the driver, have you given any consideration to the fact that the driver (or its registry entry) may have become corrupt?

If you did it this way, you might be better to out-source the driver by downloading it all over again.

by older mycroft

All it actually means is that, because each post is indented within the structure of the thread, eventually an answer to a post becomes impossible because there is no space left for any further indents.

Just create an answer and 'hang' it from a previous indent in the thread. :)

by older mycroft

My keyboard batteries expired and had to be charged up again and one of my 2 spares got pinched by Velcro, my cat. Dunno where she's put it!

I opted to use the onscreen keyboard but it is so so laborious for anything other than simple text input.

As for your problem with the above 'Maximum Message' thing - it's odd that an hour before it hadn't caused you any problem?

I'd rather keep the question/answer routine going in this thread, because if I enter into a personal email session with you, when I ultimately run out of viable ideas you will be no better off and anyone else following this thread will be left hanging when the natural sequence is broken.

So - back to the last point:

https://www.techrepublic.com.com/5208-7343-0.html?forumID=101&threadID=281266&messageID=2663274

by bean2473

Was uninstalled the printer then did a clean install of the canon driver and it still isnt working- I'm pulling my hair out over here!

by older mycroft

Is it the old one that you've always had or is it the latest one that is available online?

What is the build version of the driver you installed?

by ronspruell

You use to be able to buy the whole print head with the tri color tanks. I had this problem and bought the whole printer head and tanks and now I'm looking for the head again. I did buy a big black tank and head and I'm looking for that again. Very easy to change the head just snap it out and in but I have to finf the head first. Use to be easy to find.

This discussion is closed to new replies.