Discussion Locked

Can't Access Bios.

0 helpful
13 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
Something happened when I installed a new hard drive. My computer boots from CD. It does not access floppy or hard drive. Hard drive has the wrong drive number. I cannot access my bios to change anything. I have tried (F1) (F2) (F10) (Control+Alt+Delete) (Control+Alt+Insert) (Control+S) plus many others. My CD drive spins, quits, and that's it???

13 replies

by dmiles

Boot computer the look in the bottom left corner and it will show the desin=gnated key to enter the bios,it could be the Delete key

by hal 9000

Depending on who made the computer the keys used to enter BIOS differ considerably.

As some others have quite rightly said the Delete Key and the F2 keys are the most common ones but really without knowing the make/model of the computer/M'Board it is very hard to help you particularly if it one of the ones that shows a makers Splash Screen and hides the BIOS section from the user.

by snarkhunter

HAL 9000 is right - the number of possibilities is enormous. Your best be may be to search the web for the PC or Motherboard model to obtain the motherboard manual answer your question.

You may also need to re-set the mother board if access to the BIOS has been restricted - there'll be a jumper you'll need to set. Again, the motherboard manual will be your best bet here.

by thechas

I suspect that your new hard drive is either plugged in wrong, or the jumpers are set wrong.

Start by disconnecting the IDE cable from the new hard drive.

Boot up.

You should be able to see the POST screen and be able to press the key to enter BIOS settings.

After the POST is complete, you should get a message along the lines of:

"No Operating System found.
Insert system disk and press enter to continue."

If you do not get the POST or message screen, you have another hardware problem.

If you are now able to get into BIOS settings, make sure that the Primary Master Hard drive is set to Auto-Detect.

Save and exit BIOS setup, and shut down your PC.

Check the jumpers on the hard drive.
If the drive is the only drive on the cable, make sure it is set to Single / Master.

If 2 drives are on the cable, one drive MUST be set to Master with Slave present.
The other drive must be set to Slave.

Plug the drive back in, and see if you boot normally.

If the PC locks up again, change the IDE cable.

If you never got the POST screen, shut off the PC and un-plug the power cord.

Make sure that ALL plug in cards and memory modules are fully seated in their sockets.

Triple check all jumpers and cables.

Still having problems?

Reject my answer and post a comment with the results of the tests.

Chas

by type8324

computer doesn't boot. even with hard drive and CD unplugged. The keyboard is non responsive. Have I killed my motherboard?? Can I reinstall bios?? Is there any program that will access my motherboard from CD???

by willcomp

Had a lot to add until I got to Chas' dissertation above. Good stuff.

However this is important if you have a Western Digital hard disk.

Western Digital PATA hard disks are jumpered as single drive when no slave is present rather than master.

If you have a single Western Digital drive, set jumper to CS or remove jumper (single drive setting).

Dalton

by willcomp

Try resetting BIOS. You most likely have a BIOS reset jumper on motherboard - check your manual. If no reset or can't find any info on it, remove coin cell battery for about 5 minutes and re-insert. Ensure PC is unplugged while removing and reinstalling battery (or Hal9000 will remind us).

Hopefully, that will do the trick. If not, let us know.

by sgt_shultz

i don't know why you can't enter bios. but bet you a donut you have ide cable on 180 reversed...check both mboard and drive ends.

by thechas

Well, this is a new kettle of fish.

"Usually" when a system stops working after installing new hardware a cable or plug in device has come loose.

Start with Dalton's suggestion and clear the CMOS.

Next, keep the hard drives unplugged and remove and reseat all RAM modules and plug-in cards.

Check the connector from the power supply to the motherboard and make sure it is fully seated.

Inspect the IDE cable sockets on the motherboard and make sure that no pins are bent over.

Look over the rest of the system several times to be sure that no cable is loose or off by a couple of pins.

Make sure that the latch for the CPU socket is down and locked.

When the system starts up, does the CPU fan run?

Even though you see the light on your CD drive, you could have a power supply problem.
Either swap in a new power supply, or verify that all of the voltages are correct.

Chas

This discussion is closed to new replies.