Discussion Locked

CD-ROM IN NT

0 helpful
27 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
I would like to know what could cause NT to not recognize a CD-ROM. I already know a few reasons, but I would like a much wider answer from a much bigger audience. This would be very helpful as I am a PC Support tech whose main job is servicing NT OS probems, with a few hardware problems sprinkled on the side. Thanx.

27 replies

by hallkr

The only problem I've experienced have been with a SCSI interface. Sometimes getting NT to recognize the adapter can be a real chore.
Also a lot of CD's carry a name that in reality is not the "original" manufacturer. So finding the "correct" driver to run the device. In this respect MS "Sparrow.mpd" has saved the day on more than one occasion. When that fails I've found a nice utility called CDGod (I think it was in Driverguide.com) that can get 90% up and running.

by rooster

I don't know if this is on your list of "already know ..." but I've experienced situations where users have been listening to Audio-CD's and then changed to a data CD leaving the Turtle Beach CD-Player open. When trying to acces the CD through NT Explorer an error of the CD drive not being accessible, e.g., "E:\is not accessible, the parameter is incorrect. Hope it helped.

by kim rotbøl

another solution to the problem: check if the CD-rom drive is on the NT hardware compability list. if it isn?t it might be difficult to get it to work

:o)

by hjs

If you are on a network you may have a conflict with a mapped network drive.

by djcmac

Was the CD working/recognized before? If it's a new install, check that it's installed as a slave, and that the bios is recognizing it.

by reg hacquer

It would be easy to overlook the configuration within Disk Administrator--the drive may have been mysteriously disenabled. (Been there, done that...) Good luck!

by joshua.pyle

Well, first of all, you have to make sure the CD-ROM is on the HCL (Hardware Compatability List) for Windows NT. I know i have trouble getting Creative Labs (older) cd-roms to be accepted by NT because they want to be connected to the Creative Sound Blaster Card. I was never able to do a fresh installed onto a machine that had this setup. I rather had to created a win nt hard drive, then insert in the computer, and add the sound blaster then the cd-rom....
and, if a CD-ROM doesnt, work, usually its caused from the power, and/or scsi/ide cable not being properly connected, or having dirt/dust inside the connecter. also, esd (electronic static discharge) has a funny way of showing up at odd times.

by joshua.pyle

When you boot up the computer, does it say it installed the SCSI bios? i know that the adaptec 2940/3940 boards show you what hard drives are connected, and when or if they dont show up, then usually it means the terminator is not present or is in the wrong place. and, if you can view the scsi devices under windows, then you know it has something to do with the win nt setup. make sure you have sp4, ive had problems with sp5, so i wouldnt load that anytime soon... also, sp6 i believe is due out soon.

by gisdude

You did not specify which platform you are working on i.e. Alpha based system. Assuming that it is Alpha based, you need a specific driver for the CD-ROM (depending upon certain factors that are too involved to cover here). If you were to install a service pack or any other type of software that might possibly install a new ATAPI driver, it could lead to the system not recognizing the CD-ROM and possibly the BSOD (although I have never seen the BSOD from the wrong CD-ROM driver being installed).

Hope this helps

by jebrwn

If the CD-ROM is not on the HCL (Hardware Compatibility List) Download the Correct and current driver and add it through the SCSI deivces. (Even if it is IDE) Make sure you have good cables and properly connected.

by rms

A couple of reasons come to mind. If you build NT without a CD rom from the network using winnt /b and then install a cdrom you will get a message saying that the file system can not be identified. you need to install the cd dile system. Another reasonis if the CD's are created on a CD writer and the disc is not closed off , the cd will only be accessable on cd writters.

by jmontesi

I have seen a few cases of CD-R's that were not readable as opposed to CD's recorded by vendors. It turned out to be that the laser head was loosing strength as it got older.

by dbmerritt

I just had the situation where NT would not recognize a CD-RW that worked fine last week. It didn't show up in the list of SCSI devices at boot time. Disconnected and reconnected the SCSI cable and plugged it into a different power connector, restarted and it came right back. I just wish they were all that easy...

This discussion is closed to new replies.