Discussion Locked

Command In Dos to recognize CD ROM on Wi

0 helpful
67 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Have a game that is to be played in DOS. Game plays off a CD. When I go to DOS and try to install DOS cannot recognize my CD ROM. CD ROM is new and operating OK. Having no hardware problems.

Is there a command?

67 replies

by joeg51

Assuming the CD ran Pre 98, The mscdex.exe command should be rem 'd out in your autoexec.bat file. un rem it and dos should recognize your CD

by matt p

The initial answer did not consider the config.sys file. With an initial setup, the CD is set up in dos in both the config.sys and the autoexec.bat file. Then, as win95/98 installs, these lines are automatically rem'ed out and the CD is installed via Windws.

Using the un-rem approach, I would check both the config.sys and the autoexec.bat files. Further, I would also consider setting up a separate boot disk, at least until I was sure what would happen when Windows is rebooted with the modified files;e., boot off a floppy, setting up the drive using the autoexec and config files. Further, more than likely, you will also need to set up drivers for your mouse, etc.

I have noted this problem, both with the mouse and the CD drive; however, I have not atempted to date to modify the startup for the type of DOS boot you are attempting. It MAY impact Windows 95/98 on reboot; or, Windows may simply re-rem the files, in which case the next time you want to play the game you will have to go through the same p

by beyer

The above answers are correct in a few ways but unfortunatley some Cd Rom drives do need a dos driver to work correctly under Win95/98 so try it both ways with the drive rem 'd out in not, if still have a problem go to http://www.winfiles.com/ and you wil find your device manufacturer there and download the lastest drivers. Another thing is i have heard Win98 does not really like dos base programs, i have never tried to run one so i cant say for sure.

Mark

by mkelley

You can also set up a shortcut in Win98 that forces a reboot to DOS and establishes DOS environments for that DOS session including the CD Rom drivers. You should have a line in your config.sys that looks like;
DEVICE=c:\*.sys /D:CDROM1, where * is theame of the driver for your CDrom drive. Then in the autoexec.bat you should have a line that looks like; C:\MSCDEX.EXE /D:CDROM1.

by rcastellan

The drive should have come with a driver disk. If thats true just go to an a:prompt and type install. It will install the needed drivers in the autoexec.bat and the config.sys. Reboot and the cd-rom should be recoginized in DOS. You may need to install thse same driver line fronm the autoexec.bat into in the Dosstart.bat file if the first option does not work. If you do not have a driver disk you can download just about any driver from drivers.com.

by davidf

Umm, i have a program that install every cd-rom drive in dos so if u want, u can mail-me and i will send the program to u.

PS:U have to have mscdex.exe

by hallkr

You didn't mention what the name of the game is but I'll assume it's a recent game like Quake for example. Some games run in DOS but need to be installed in Windows. Quake is one of those type games that, depending on your system configuration, can run invarious environments including Windows, Open GL, DOS etc. Try loading the CD in auto start(Windows) and follow the install prompts. If that does work "Explore" the CD for the "setup.exe" and run it. Most game manufactures don't require you to know how tonstall games from DOS, it too rustrating for most people and takes away from an enjoyable game experience. If that doesn't work, ask for a refund. If they wont refund your money... donate it to TR for the new flying disk upgrade. Good-Luck!
Ken

by jdp106

IT'S POSSIBLE THAT YOUR DOS VERSION IS TOO OLD,OR DID YOU TRY TO INSTALL THE GAME USING THE DOS PROMPT ON WINDOWS,BY PROMPT WINDOWS, THAN YOU SEE WINDOWS CD:\ INPUT CD..ENTER, THAN INPUT THE LETTER FOR YOUR CD DRIVE EX: D:\ ENTER, THAN DIR: ENTER THEN YOULL SEE WHATS IN YOUR CD, THAN CHOOSE SETUP.

by jaras

bueno primero dime cual es el juego que quieres configurar y que marca es tu unidad de cd-rom para proporcionarte el controlador que debes usar y despues te digo que instrucciones debes de seguir para ponerlo a funcionar

by jesselou

first i would advise jedeah before executing
the dos games there is a startup disk utility
hidden in win 98.go to start,programs,click
explorer,then program files,you can see the
PLUS click it,select system and there it is
the nocomp.exe click this oe and it will
prompt you to put your floppy disk in drive
a:\ this startup utility disk is intended for
your most loved dosgames.
next, is my propose resolution to your cd
problem: go to your c:\windows and type dosstart.bat if it will notwork, andou are
in a hurry place your windows98 bootable
diskette that came together with your win98
cdpack when you bought put it on you drive
a:\ and reboot this will recognize your cd rom temporarily. now the most difficult part
is to properly configure yor cd rom in your
cmos from there you can set the correct settings, whether it is in the primary slave
or somewhere. after that save your settings
and exit. reinstall your cdrom generic driver. artemio@emirates.net.ae

by joemcse

If you are exiting windows to get to dos, make sure you modify autoexec.dos and config.dos as well.

by hanover phist

If the game is installed go to that dir and creat a short cut to the file that starts the game. Right click on the shortcut and chose proerties. Then chose advanced in this nenu there is an option there that lets you run a dos program and ignor windows. Pick this one and then go through the other options and make sure that programs in background are not running set all the memories as high as they will go. This has worked for many of my old dos games but not all. Sorry I can not remember all the choices in the menues but I have no dos games at work to setup and look at this is just from memory. Good luck

by saulsteenbok

hi,
edit your config.sys in your root directory and try this command:
device=c:\windows\command\oakcdrom.sys /d:oemcd001

then edit your autoexec.bat file and add this command:
c:\windows\command\mscdex /d:oemcd001

you might need to add these commands to your autoexec.dos and config.dos files.

by dabson

Since you're in Windows 98, there's a quick, easy way to play your game. First, you need to make a Windows 98 start disk. Do this by going to Start -> Settings -> Control Panel -> Add/Remove Programs, click on the Startup Disk tab, then click on the Create Disk... button. Win98 will ask you for a floppy disk, so throw an empty one in to your floppy drive. Once Windows 98 is all done, shut down your programs and then restart Win98 by going to Start -> Shut Down..., selecting Restart, and clicking OK.Make sure you leave the disk in the drive.

Now your computer will restart and load from the floppy drive. Follow the prompts to get the computer to recognize your CD-Rom, etc. Once you get to the A:\> prompt, you're ready to find and run your game.Switch to the C: drive by typing "C:". Now following your DOS games instructions on how to run the game from DOS.

The next time you want to play a DOS game, put the disk in the drive before you turn on your computer. Make sure the disk is out of the

by budi_novit

Make sure you still have file mscdex.exe and driver for your CDrom drive
Then edit your autoexec.bat config.sys

Or if you have a driver disk from your CDROM, you can install (not setup)
CDROM drive for DOS mode.

by prugh

an EZ way to create CD Rom support with only Win 98 CD is to create the FAT32 boot disk which supports many CD Rom drives - on Win 98 CD - in \Win98\tools\mtsutil\fat32ebd there is an executable FAT32EBD that will create a boot disk - you can then copy drivers to hard drive and modify config.sys / autoexec.bat

by jacooker

Why worry about a command. Get rid of the DOS game an get a new game that will run under 98. Why would you want to run a DOS game? If you are running 98, the newer games out are much more better.

by rustys

I have had this problem before. Step by step instructions also included.

Goto you windows directory and find the file called: Dosstart.bat
Open it in a text editor (do not run or open the program you will exit windows and need to restart).

Have acopy of you CONFIG.SYS handy and locate the device line that loads your cdrom driver. It might look like this:

DEVICEHIGH=C:\CDROM\OAKCDROM.SYS /D:CD1

Take the /D:CD1 and place it on the at the end of the MSCDEX command line. Your may vary slightly just look for the /D:??????.

Example:C:\WINDOWS\COMMAND\MSCDEX.EXE /D:CD1

Save the file and then try it. If you have futher problem or questions eamil me: rustys@mailcity.com

by davewiz

try using dosstart when in ms-dos mode if the cd was installed pre-win 98 it should come up from there if not then then use an ide-apti driver.

by tripkirk

There are actually two commands that are needed for the CD ROM to be recognized in DOS. The first will be in config.sys and will read something like "Device=c:\cdrom\atapi.sys" where the actual file is the real mode device driver that applies to your system. If your CD ROM did not come with a disk, you might be able to get the drivers from the manufacturers web site. The second command will be in autoexec.bat and it will be "c:\dos\mscdex d:drive name" where the drive name is the same as the name that the config.sys driver uses after the part I typed in above.

by jeknull

Answers before are right, but the least confusing is the one that says that normally the CD-ROM drivers are not installed to run under DOS. Just get your CD-ROM driver disk (or go to www.driverguide.com and download a suitable driver) and Start -> Run -> type "a:\install" without the quotes, with the disk in the slot. There are two basic / generic D-ROM drivers, you should try to see which one is the one you need.

by webworld1

in windows press start run type sysedit this will bring up the system files
edit theauto exec.bat file and insert the following line
c:\windows\command mscdex.exe /d:mscd001 next time you boot into dos you will have a cd driver present hope this is ok

by saulsteenbok

enter the following command in you rstartup files (autoexec.bat and config.sys). the easiest way to edit these files is to choos run from the start menu and run sysedit. in your config.sys enter the following line :

device=c:\windows\command\ebd\oakcdrom.sys /d:oemcd001

in your autoexec.bat :

c:\windows\command\mscdex /d:oemcd001

this is assuming you have win 98.

by saulsteenbok

enter the following command in you rstartup files (autoexec.bat and config.sys). the easiest way to edit these files is to choos run from the start menu and run sysedit. in your config.sys enter the following line :

device=c:\windows\command\ebd\oakcdrom.sys /d:oemcd001

in your autoexec.bat :

c:\windows\command\mscdex /d:oemcd001

this is assuming you have win 98.

then reboot your machine

by rhumphreys

There are a few ways you can get around this problem.

1. Try installing the program using a DOS session. (START > RUN > TYPE- COMMAND > SYNTAX FOR INSTALLATION)

2. add the following lines to your config.sys and autoexec.bat

Config.sys

Devicehigh=c:\windows\command\oakcd.sys /d:cdrom

Autoexec.bat

LH c:\windows\command\mscdex.exe /d:cdrom

This should work fine

by frush

There are a few things that you may need to do to have your CD recognized from DOS. Especially if the CD is older, you may need a 16 bit driver loaded by way of your config.sys file. The typical form this takes is:
Device=C:\location_of_driver\driver_name.sys /D:MSCD001

Depending on the driver, there may be other arguments to be added.
Once this line has been parsed by the operating system at startup, you will have access to the driver file listed (driver_name.sys above), and it will produce aninterface through MSCD001 to the MSCDEX.EXE program.

Note that you can call this interface anything you want, but when you access this interface in the arguments that MSCDEX.exe requires, you refer to it whth the same name. An example of a call to mscdex.exe might look like this:

C:\WINDOWS\COMMAND\MSCDEX.exe /D:MSCD001 /E /M:6 /L:Y

This would call the device driver example above, and would try to use extended memory ( /E) it would set the number of buffers to 6 (/M:6) and would set the drive l

by *robert

I concur with #2, however it removing the rem statment does not work, try rebooting and use the F8 key to come to a command prompt only. Your CD Rom should have come w/an installation disk. From the command promt run the install program. This shouldallow the CD Rom to be run in dos.

by mrditzo

I have seen this problem many times and have cured it with a simple fix of making another Win98 emergency boot disk, and adding to the autoexec.bat file the command line for the game ie: C:\NASCAR, and always booting it with CDROM Support.

by pc dr.

4 FILES ARE NEEDED
IN THE ROOT DIR OF C:
MSCDEX.EXE
AUTOEXEC.BAT
CONFIG.SYS
CDROM DRIVER? MTMCDAI.SYS FOR MITSUMI
CONFIG.SYS:
DEVICE=C:\MTMCDAI.SYS /D:MED
AUTOEXEC.BAT
C:
CD\
MSCDEX.EXE /D:MED

THIS WILL GIVE YOU A D: PROMPT

by dmitry

In config.sys file you must have command
devicehigh=c:\oakcdrom.sys /d:000
in
autoexec.bat file you must have command
c:\windows\command\mscdex /d:000

if you want your cd-rom to work afrter chhosing start->shut down->restart to msd-dos modethen in file dosstart.bat located in windows dir you must have a line like in a autoexec.bat

P.S
Oakcdrom.sys is located on win 98 emergency boot disk. and will work if a cd-rom is ide :)

This discussion is closed to new replies.