Question Locked

Compaq Recovery Disk/Optical Drive incompatibility

0 helpful
27 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I have a Compaq SR5123WM that has a new hard drive. The old one crashed and is not revivable so I can't access the D drive where the recovery info is.

I tried using the Recovery Disks that came with the computer, but I get an Error loading operating system message.

I contact technical support and have told me so far that the recovery disks must be defective so I ordered new ones. The optical drive must be defective so I installed Windows XP from an old machine that I no longer have.

I can open the disks on a different computer and can see files on the disk. So I've ascertained that the optical drive works on the Compaq and there are files on the disks, but they don't want to work together.

Does anyone have any ideas on what the problem is?

Pam

27 replies

by seanferd

You may need to enter BIOS and change the boot device order so that the optical drive comes before the hard drive.

F10 seems to be the key to Enter System Setup on a Compaq, but look to see what key is offered for this function as the system starts to boot.

by pjsnyder7082

I have changed the boot device order and that hasn't helped.

by rob miners

Use the following steps to recover the computer from a set of recovery discs (either CDs or DVDs):

Before recovering, back up files from the My Documents folder and from other folders you may have created.

Disconnect all connected devices (such as the Personal Media Drive, USB drives, printer, and fax), remove media from drives, and remove any recently added internal hardware. Do not disconnect the monitor, keyboard, mouse, and power cord.

Turn on the computer and press the Esc key when the first logo screen appears.

Insert the first recovery disc into the top CD or DVD drive.

Use the Up Arrow and Down Arrow keys to select the CD or DVD drive containing the recovery disc, and press the Enter key to start.

If a screen displays "Press R for recovery options", press the R key.

A screen with a list of options should appear: R, F, and Q. These options can change depending on the state of the hard drive. For example, if the hard drive is new, only R lists.
Select one of the following methods depending on the type of recovery method you want to perform:
Press R to perform a standard system recovery.
Press F to perform a destructive recovery. This will format the hard drive. If the hard drive is new or has had the recovery partition damaged, this option will also create new partitions and format the drive.
Press Q to quit recovery.

Read and respond to each window and screen that appears.
NOTE: When changing discs, do not press the OK button. Instead, wait for the drive to read the disc and automatically continue the recovery.

NOTE: If you are using a supplemental recovery disc (select models only), you must remove the supplemental disc before restarting the computer.

After the System Recovery is complete, the computer restarts and continues into Windows setup. Complete the setup screens and wait until the computer finishes the setup.
NOTE: It may take a long time to complete Windows setup. This time varies and may take over several hours. Recovery times are most affected by using recovery discs that were ordered from HP and/or the amount of files that were stored in the user account folders (Like My Documents and the Desktop).

Before using your computer, update and protect your computer. For more information, refer to Things To Do After Performing a System Recovery in Windows XP . http://h10025.www1.hp.com/ewfrf/wc/document?lc=en&dlc=en&cc=sg&product=3443290&docname=c00276693

by rob miners

Error Loading Operating System

http://www.computerhope.com/issues/ch000730.htm

This issue may occur if your computer BIOS does not correctly manage or support the capacity of the hard disk on which you are installing Windows XP.

To resolve this issue:

Make sure that you are using the latest BIOS revision for your computer. Contact the computer manufacturer to inquire about how to obtain and install the latest BIOS update that is available for the computer.

http://support.microsoft.com/kb/326676

by pjsnyder7082

How do I go about flashing the BIOS when there is no operating system on the machine?

I did just notice that there is a message on the boot scrren that says "Default BIOS settings have been loaded due to BIOS update or check sum issue."

That's a whole nother problem, isn't it?

Pam

by pjsnyder7082

Thanks for your speedy reply.

First of all, I didn't mention these parts that I have tried, but here goes.

When I received the computer, it had been with the Geek Squad for about 6 weeks getting a new hard drive. The customer noticed right away that things were not the same so she asked me to look at the computer. It was running a Dell 64-bit version of Vista Home Premium. The computer came with Compaq 32-bit Vista Home Premium. I figured to just do a recovery from the cd and everything would be okay.

I followed HP's instructions for doing a recovery using their Recovery Disks that the customer had given to me. They didn't work. I made sure the CD group was first in the boot order. I put the first disk in, turned off the computer by holding the on/off switch in for about 5 seconds. Then I restarted the computer. The recovery screen is supposed to come up at that point. It didn't. It booted to the 64-bit Dell version of Vista.

I contacted HP support via email. The guy tells me, it's a faulty optical drive, corrupted disks, or 64-Bit operating system in the drive is interfering with the 32-bit operating system installation.

I was able to install other programs to the computer before trying to do a recovery so I figured there was nothing wrong with the optical drive. I can open the recovery disks on another computer so I figure there's nothing wrong with the disks. So I used Kill Disk on the hard drive. The optical drive worked for that procedure.

At this point there is nothing on the hard drive.

I installed Windows XP at this point hoping that having a 32-bit operating system would allow me to use the HP Recovery Disks. I used the HP procedures again for doing a Recovery from the disks. The optical drive flashes like it's trying to read the disk, but it eventually boots to Windows XP. So I used Kill Disk to wipe the disk again.

I ordered new Recovery Disks thinking that perhaps there is something wrong with the Recovery Disks. The new recovery disks also do not work. Again, I can open them on a different computer and see that there are files on them, but the Compaq does not like the disks.

There is no operating system on the machine at this point. I tried using the Mem86 test on the ram but it wouldn't work using the optical drive. That could be because there's no operating system. I'm not sure.

I have also replaced the CMOS battery.

I never get to the opening recovery screen to begin a recovery with the cd's, but I know that the optical drive is capable of installing an operating system because the Windows XP installed.

Grrr.

Pam

by rob miners

go back into the BIOS and set the CD as the first boot device. Save the settings as you exit the BIOS.

Is killdisk on a CD or a floppy?

If it is booting from the CD it should come up and ask to press any key to boot from CD.

Also by pressing escape at the startup and selecting to boot from the CD should work.

I can't understand why 64bit was installed on the System.

We really need to be able to boot from the recovery DVD but just in case it needs an Active Partition try this with your XP CD.

You have deleted the Primary Partition and you will have to recreate it, try this by pressing Enter after each command. Adjust size=20000 to the required size. 20000=20GB 30000=30GB etc.....or leave it blank to use the full drive.

using DiskPart. For example, from a command prompt, type:
diskpart
select disk 0
clean
create partition primary size=20000
select partition 1
active

Now type

EXIT to exit the diskpart session

Try the recovery DVD again.

Edited for commands.

by seanferd

Six weeks for a hard drive? maybe they had problems booting from the optical drive as well?

I wonder if it matters how the drives are set up.
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01077676&lc=en&dlc=en&cc=ca&lang=en&product=3443290

Parallel ATA

* One 40-pin UltraDMA 100/66/33 connector
* Supports PIO, multi-word DMA modes
* Supports two PATA disk drives on one PATA ribbon cable (two drives total)

Serial ATA

* Four SATA connectors:
o SATA1 = Black
o SATA2 = White
o SATA3 = Blue
o SATA4 = Yellow

* Supports 1 SATA-150 or SATA-300 disk drive on each SATA connector
* Speed up to 1.5Gb/sec or 3.0Gb/sec, complying with SATA 1.0 and SATA 2.0 specifications

NOTE: The faster rate of 3.0Gb/sec requires that both the hard drive and the motherboard support it. If one or the other does not support 3.0 Gb/sec, the PC negotiates down to the slower 1.5 Gb/sec.
RAID

* Some Nettle2 models ship with RAID (model dependent)
* nVidia's onboard RAID solution is called nVidia MediaShield Storage
* RAID modes supported*:
o RAID 0
o RAID 1

by oh smeg

If the Boot Order is set correctly and it is booting off the Optical Drive but comes up with Error Messages of unable to find files this is a sign of Faulty or Mismatched RAM.

What happens is that when you have Mismatched RM you hit a minor Timing Issue that the Windows Installer can not cope with though when Windows is Installed it seems to work perfectly.

You need to test the RAM with MemTest86 available here

http://www.memtest86.com/download.html

If this fails to show any problems remove any extra RAM that has been fitted or remove all but 1 Stick of RAM install the OS and when this is finished refit the remaining RAM. :)

Col

by pjsnyder7082

As far as I know, it has the same memory that came with the machine a couple of years ago. The MemTest86 isn't working with the optical drive.

I tried taking out a stick of memory and using the recovery disks. Still didn't work.

Pam

by seanferd

It has to be the ISO file for the optical drive.

And you are burning the ISO as an ISO Image File, not just copying it to optical disk, correct?

I'd guess that you are doing this, but I'm just checking.

Also, FYI, MemTest runs without any OS, it boots itself as a tiny, single purpose operating system. So, no OS would need to be installed on the HDD.

edit:
http://www.memtest86.com/
for their instructions.

by seanferd

I've never tried this, as far as I know.

Edit: Seems it should work just fine.

by oh smeg

After all we have had 64 Bit Systems for a long time now even if they do come with a 32 BIT OS Loaded.

The switch to 64 Bit hasn't been held up because of the Hardware but because M$ at first and then the Hardware Makers couldn't support it.

Previously when we moved from 16 to 32 Bit M$ was still an infant and could change tack quickly and be ahead of the Hardware developments or at least up with them. Now M$ ha become a Giant Behemoth and is the one dragging it's feet in new developments. I can remember going to a AMD Launch of their then new 64 Bit Capable CPU and they where then giving away free 64 Bit Versions of XP with every CPU that you purchased.

The 64 Bit Version of XP was buggy and fairly useless an the driver support was even worse.

Col

by rob miners

with the software on it to flash the BIOS if you haven't access to a Floppy drive.

You receive this message Default BIOS settings have been loaded due to BIOS update or check sum issue because you didn't go into the BIOS after you changed the battery and reset and save the settings.

by seanferd

I would never do that, according to everything I know about BIOS-flashing.

by pjsnyder7082

within the OS, but there's no OS to tell the computer what to do with the file on the disk. It's the OS that tells the computer what to do with a .exe file. I would think I would need bare minimum DOS running.

Pam

by pjsnyder7082

go into the BIOS after I changed the battery. I changed the date and time and boot sequence.
Pam

by rob miners

being detected properly in the BIOS. Did you use the CD rom drive to use the disk wiping software.

by seanferd

The OS has nothing to do with this. If you boot from other media, the OS installed on your primary boot partition does not come into play whatsoever.

If you have an exe file for flashing the BIOS, you need to run that file to install it on removable media.

by pjsnyder7082

The CD group is set as 1st in the boot sequence.

Killdisk is on a CD that I burned my self. It came from here: http://download2.lsoft.net/boot-cd-iso.zip It will run from the optical drive no problem; therefore, there should be no problem with the DVD player.

My guess is that the Geek Squad figured it's a 64-bit computer, it should have a 64-bit OS. What I'm blown away by is the fact that the OS came from Dell and they put it on a Compaq. That probably violates somebody's rights.

I'm not sure how to get from the Windows XP cd to a command prompt, but here's what I have done.

I inserted the Windows XP disk. Hit CTRL ALT Del and up comes the Windows XP installation screen. I got to the place where the partitions are created and there were already two partitions on the drive. I deleted both of them and recreated them and the F3 Quit the installation.

I inserted the HP Recovery Disk and restarted the computer and now I get the error "Boot Disk Failure. Insert System Disk and Press Enter."

Sounds like the Recovery Disk isn't a bootable disk.

Pam

by rob miners

at startup and selecting to boot from the CD. If so it may not be bootable. I would get back in touch with HP and let them know about the problems that you are having with the DVD.

by pjsnyder7082

when something is loaded on it. I can load an old Windows XP OS I have on it. I just can't the the HP Recovery Disks to work.

Pam

by pjsnyder7082

I had a copy of MemTest on a CD that I'd used before that worked, but it didn't work this time. I just downloaded the program again and burned a new cd and it's working.
I'll have to get back to you on the results.

Pam

by pjsnyder7082

is detecting the new drive and yes, I did use the DVD player to use the disk wiping software.

Pam

by oh smeg

From within Windows you add it to a Boot Disc and run it from there.

It makes no difference what OS is on the HDD as for all intents & purposes you could remove the HDD and still successfully Flash the BIOS.

Col

This discussion is closed to new replies.