Question Locked

Computer powers off by itself and does not start....

0 helpful
13 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I've recently encounter a situation with my computer... The computer was completely normal until couple days ago when I tried to boot up my computer from a stand-by overnight. I've noticed that the computer is still on (due to the motherboard light and the stand-by flashing led on my case), however, when i tried to press the power-on button, nothing happens, so I do what many would have done...hammering the button, nothing happen....so I manually turned off the switch in the back to cut the power.

After turning the switch back on (motherboard light on), i press the power-on button, and for a split second (1/2 a second or so) the computer was on and then turns right back off; so again, i press the button again, nothing happens; as a result, I flip the back switch on-off-on....same thing happens again, 1/2 second of power. So I opened up my computer, took off everything on the board except the switch that connects to the case and the power supply; again, same old story, 1/2 a second worth (i can tell from the motherboard fan). So I'm starting to think it's the power supply that's giving me the problem...but, the power supply (X-finity 600W ps) was only 1 month or 2 old and it's fairly new.

However, i replaced the power supply with a old 550w ps that i had before and tried if the computer would run, but again, same thing happen, which i'm assuming it's not the power supplies' fault or could it..? So now i'm assuming it's the power switch that connects the case to the motherboard that's the problem...

But again, I left the computer overnight in the "on" position of the power supply and the next morning, the computer were able to turn on normally when i pressed the case power on button. BUT!!!, after the computer stays on for like 10 mins, the computer turns off suddenly (power loss), and the whole thing repeats itself again...

I have also tried cleaning out any dust that accumulated inside the case/fans (although not so much because all the components are new) and it's giving me the same problem.

I didn't want to come to this, but I have tried almost everything and running out of ideas of what's wrong. This rig that I built was only 5 months old...everything was brand new except for the optical drives, one of the secondary harddrive, and the computer case itself...

Any help is much appreciated and thanks for anyone who can help me out!

13 replies

by mjd420nova

This sounds like a motherboard failure OR the most common problem I've found with new builds is the shorting of the power supply by one of the standoffs that the MOBO mounts on. Some are required to have an insulating washer between the standoff and the board. This may have slipped out of place or may be missing. Repeated hot and cold cycles will cause the MOBO to shift a little on the standoffs and one may be shorting the power supply.

by dimfob

First of all, thanks for the help.

I would doubt that it's the motherboard's failure since I was able to run the computer normally after a "charge-up" like action done on the computer...but like I said, that only lasted 10 mins of normal run time and it went back to the same status...

So if it is the mobo's shorting on its mounts, I should add washer underneath the screws where I attached the mobo to the case holes? (between the case and the mobo?) Oh and these washers, is there a specific type that I need to get? (i.e. Would Fry's have them? =D )

Thanks so much for your time and help.

by finalxii

hey man i've got the exact same problem, recently custom built my computer, had it on stanby during the night and... yeah exactly what happened to you. All the parts are new and very recent, dunno what to do about this, did you ever find a way to fix this? thanks a bunch ! I'm pretty desperate...

by older mycroft

It would seem the motherboard shorting against the case may have been the answer, since the OP didn't come back with any more problems.

by finalxii

Thanks, yes I've read the previous post as well as a bunch of things on the internet. Here's what I did:

I put the mobo outside the case plugging only the cpu, no ram nothing else, and I still had the problem. I then removed the cpu fan and tried installing the cpu again, put the power on and bam it worked.

So alright i put the mobo back in its case, replug everything, try to power it on, same problem all over again, starts for a sec then turns off and i have to unplug it if I wanna try again cuz if i press the power switch right after nothing happens at all, not even for a split second.

So hell i open the case again, press on the cpu fan, beeing able to move it a milimeter, plug it, press power and it works, finally.

BUT, it was not in the correct outlet since i was plugging in the computer directly in the outlet rather than having it go trough a powerbar, since all the tries i've made connecting it to a powerbar ended up as failures. It only seemed to work plugged in directly in the outlet. So i move the computer gently, plug it back in in the other outlet it my room and.....

wont boot again, played around with the fan again, nothing. ONly starts for a sec then shuts off...

From what i can tell the problem is either with the cpu or the mobo socket in which you install the cpu..still, im clueless on what to do. I'll try reinstalling the cpu again from this location but i doubt its normal having to move the computer so carfully to prevent the fan which is huge btw , Zalman 9700 led, moving the cpu and thus preventing it from booting...

I need help!

by finalxii

I have an intel Q6600 cpu.

I got it to work for a while today, removed the cpu, cleaned the thermal paste and put a new layer of it then everything back. Tried starting the computer, didnt boot, played with the fan a bit, and it finally booted up.

Got it to run for a while, but my 2 geforce8800gtx were overheating like mad, even the back of the case was burning hot around where they were. Got to play some oblivion to test it but it was lagging a bit which doesnt seem possible considering the monster system.

I had to go so i turned the system on, and it kept restarting instead, which is odd, so i manually pressed the power button to turn it off. When i came back I had the same problem all over again, fan starts spinning for a split second when i press power and thats it.

... now im really confused

by notmuch005

I am thinking it is most likely the front panel power button or switch's problem. However, one of my friend said my computer's power supply was the problem. It now seems that it really is the front power button/switch problem. I am going to buy one and replace the old one but I don't know where to find a new one. If you know or anyone out there knows where to buy or what the true problem is, please reply here! Thank you very much!

......
(several days had passed...and now I have some new idea about this problem...)
Please read my read my post, "Yeah, Man!"

by hwoha

And I changed the casing, thinking it has something to do with a faulty power on button. It didn't solve the problem. A few friends told me it could due to faulty M/B, PSU or RAMs. Personally i feel there is a high chance that the faulty PSU is the culprit.

by notmuch005

I just changed the power supply unit. Now, PC works very normal! The culprit is the PSU for sure!
I now think that many power problems are due to PSU malfunction usually!

by hwoha

and thanks for informing us your solution here. I think I will get a new PSU for myself too.

by ghufrancc

I have a Same problem. My PC turn off itself and when i remove power and plug in again its working. Its only happen sometimes not daily my PC run 20 hours or more maybe Daily.
My system is brand new everything without power supply im using dell 350W.
Spec is:,
Intel DG41RQ
C2Q Q8300 2.50GHz
Kingston 4GB 800MHz(2Gb * 2)
Western Digital Caviar Green 1 Tb
Sea-gate 500 GB Barracuda
Sony Super Drive
Nvidia 8500GT 256Mb DDR2

This discussion is closed to new replies.