Discussion Locked

Computers Rebooting on their own

0 helpful
46 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Hi. I'm running NT 4.0 server and NT and 98 workstations.Sometimes some of my computers are rebooting on their own, without any paticular reason.Could someone tell me the reasons why it could happen or tell me what to look for in order to eliminate all the possibilities.Thanks.
Alex.

46 replies

by baklaguy

When they reboot are they cold booting or soft booting as in the CTRL-ALT-DEL escape sequence?

by aszygowski

Hi, Thanks for your response.

I think it is a cold boot, but I don't totally know the differance between the two.

Alex.

by rsalvana

How is your power situation? Do you use UPS's? If you do, are they any good? A loss of power without a UPS, or for a duration longer than the UPS can handle, will reboot your machines.

Cold Boot = cycle power to reboot
Warm boot = press resetto reboot

by eksm69

hi

possibilities for rebooting follows

1.check ur electric power inlet

2.check ups output if u have any

3.check earthing in ur power inlet as well as at ups output

4.check ur smps output

5.remove virus if any(boot sector virus)6.if ram bad it also cause the machine reboot

7.system files may be damaged

8.reconfigure the drivers

9.check this with minimum hardware configurations

10.if above tips not helps u contact ur system vendor

kindly reply me the results

by trishd

Prior to Y2K we had a planned power outage and found that some of our PC's rebooted too. Look in setup (when the PC first boots up) and see if you can change a setting that has to do with power detection.

by mismgr

We had some systems that were doing the same thing....I resolved this problem by booting up the computer in safe mode, then ran a full scandisk on the drive. The problem then ceased. This was only happening on my Windows95 systems. Hope this helps. Scott

by paul

First thing to check is power managment settings in your bios setup.
I have come across this problem if the pc is soft power switched and you have the wake up on lan function enabled or any of the other wake up finctions enabled ie: a serial devicewhich could also mean a modem. A faulty nic once turned off pc's on my netwotk.

by chris.bianchi

Are all of these the same model systems? Are all of their cases similar in design? NT is very resource intesive and problems in system design become more apparant as the OS becomes more demanding. For example, a problem with a PC design might never be found when someone uses DOS, but when the upgrade to Windows 95 or 98, problems arise. Things like graphics, sounds, multitasking, device management, etc, are all very taxing to a system. This forces a system to run at higher and higher temperatures. Intel, AMD, and Cyrix make their chips fault-tolerant to ambient temperatures. When a chip gets too hot, the system will reboot itself for a quick "cool down" prior to damage. If this happens frequently, the system design may be at fault. Due to the taxation of the OS, this may or may not occur with lesser Operating Systems (such as DOS, 3.1, 95 or 98, linux, etc) even on the same machine.

by kevins

It's probably the Bios settings. I would check there first (as previously mentioned).
Disable any power management in the bios and also check the UP settings (again, previously mentioned. The UPS devices will reboot the computer if serially connected to a PC and configured properly. If the UPS device has scheduled tests, this could cause a reboot also.

KevinS

by charles forchu

Hi!

In windowsNT, right click on my computer, then properties, then click the startup shut down tap.

Under Recovery, on the bottom screen, You will see a check box that states " Automatically reboot". Make sure that box is unchecked.

If thebox is checked, WindowsNT will automatically reboot each time a stop error occurs, regardless of how small and insignificant the stop error is.

I hope this helps.

by snelson695

We were experiencing problems with laptops shutting down and rebooting during active use. We eventually determined that the laptops were overheating. We started propping up the back edge of the laptop to create a space between the bottom of the unit and the desk. don't know if this will help, but I thought I'd add my two cents.

by vhall

You should check your RAM. Sometimes faulty or low grade RAM will cause lockups and also system restarts.

by kishu_k

u'r ram may be at the fault

sometimes faulty device connections or ram plugged in incorrectly may cause hangs and reboots....

Also check the system with another power supply....it may be very surely the culprit if no other reason is behind....

by richard

In addition to faulty RAM, we had a client whose systems rebooted frequently until we removed the extra mis-matched RAM they had installed. Different chip speeds, etc, in the same system can cause problems. Make sure all RAM is identical in a single box.

by jorgeag

I think one of the main rasons why a computer reboots on its own, is the over heating problem, check the power supply fan, the CPU fan, and the correct settings for the CPU (Voltage etc,). I hope this help you :-).

by bill.brightwell

You may have the configuration setup to reboot after a BSD. NT defaults to this setting. To check this out, click Start, Settings, Control Panel, System. Go to Startup Shut down tab. Bottom entry on screen under Recovery. Automatically Reboot after BSD should not be checked!!! It may be that are having Faults on the server and it keeps rebooting because of this configuration.

Hope this helps on your way to resolution.

Bill Brightwell

by mefindley

I had an office full of Windows 98 machines rebooting on thier own. I found out that the only ones that were rebooting were the ones with internet access. I checked Micron's site, downloaded different versions of internet explorer and Netscape, Scanned for viruses and nothing worked. The only fix I found was to format the hard drive and reinstall windows

by its a secret

If your antivirus does auto update , it may reboot you pc when done. Mcaffe does this. You may need to check the settings

by jezi

I have had that problem before - but not on an NT . The problem turned out to be from the the power cord plugs that plugs into the back of the PC. For some reason the was not making proper contact or was defective. The problem went away after I change the power cord. Hope this helps.

by drdon

This symptom is usually pwer related. If they are the same machines, check the power cabel from the UPS or serge protector to the connector on the power supply. They must be tight. Next, check the power supply its self, if it is on an older machine it could be the power supply is going bad, or a weak connection inside.

by mkleidel

You say this happens to both NT and 98 systems? Are they also all the same brand and model? If the problem started with these different systems at the same time, then think about what they all have in common. Look at those issues only. A loose power cord, for example, might be a problem for one system but would be rather unlikely (or extremely coincidental) for all of them!

Did these systems all get upgraded with new hardware or software recently and about the same time? In my experience, it's usually been a bad device driver causing the re-boots. That's typically the only type of code that can cause a system fault at such a low level as to force a reboot (applications usually only cause high-level faults which the OS safely traps). Even in the case of NT, where the system may be configured to auto-reboot on error, the issue comes down what exactly caused that error in the first place. Again, in my own experience I've seen this problem with network drivers, backup tape drivers and (possibly) an HP Laserjet 6 driver. Be suspicious of any really new hardware you may have implemented where the driver software is an early release and may still have lots of bugs to be worked out (a new CD-Writer or wireless LAN card, for example)

- michael

by pkatia

Hello there

One of your devices is not faulty..Please unplug one by one and then plug them one by one..testing each one..it could be the Nic,Sound card or RAM..

Kindest regards

by rewillia

The cpu fan may not be functioning properly.
Replace the $10 fan.

The reset switch may be shorting out.

by phelms

I've had the problem of a Windows 98 machine mysteriously rebooting after accessing an NT based VPN through a modem to an ISP. At no other time does it reboot like this.

by riversdale28

I am running Windows 95.
It has only started to happen in the last couple of months.
Could it be a fault CDROM drive?
Are there BIOS settings that I should examine also?

by stinkyjones

Before I came on board our consultants bought bargain basement machines with cheap ATX cases--seems like the CPU gets hot and just shuts down. We don't have this problem with the older, non-ATX cases--probably because the power management isn't integrated with the software. Every time it gets warm in the building, I get 5-10 calls about this happening. Our soulution: get better equipment.

by tjc01

I had the same problem with my network every summer. The computers would randomly reboot for no apparent reason. I changed cpu's tried new cases, and so on. Finally I had the hydro company come in and test the current over a period of 12 hours. Theyindicated that when the airconditioners clicked on, they would drop voltage momentarily. The hydro company installed another transformer and I haven't had the problem since. May work for u and again may not.

by shanghai sam

Could it be a power related or lack of quality power that brings them down or perhaps an aberant program such as Net Bus or Back Orifice has been installed on to your network? These being sometimes called a virus but a difficult file to find by virus software. space.exe as in _.exe is the BO file. A hacker (not a true expert hacker but a script kiddie or experienced aberant program user) could be rebooting your pc's or crashing them. First off are they connected to the net? Do others have access to them? Brought any disks/files home from school or work that you placed on the HD.
What type of hardware? Are they all the same system or a variety of harware types?
Power is a problem - In Seattle - Seattle Light rarely supplies thebonafide 220 or 240 current that gets split to 115/110 to the users and many computer networks have problems running when installed at a new location that had no previous network. Is there a flex fuse on the curcuit or a bad breaker? Many things could cause this.
We once had a Mechanical engineer destroy a Sun Sparc station by flipping the breakers on and off in one area of a Major Hospital and Research Center. Appeared to kill the power supply at least on it. Read 2nd too!

by qdid7of9

Wtf I'm no transient as it says here above in my first message, hmm perhaps that won't show. Anyway her we go.
I'd check up on BO and Netbus etc if you are on the net. Expecially a connection like cable modem or dsl. These are best targets for attacks to see what we can do to your system. Essentially Bo or NetBus and some others can be used as remote access software but can be used to be much more destructive than PC anywhere. There are also various "Nukes" that can be launched at your ipaddress to crash stuck blues screen of death or cause a
reboot if designed too. These are a type or DoS Denial of Service Attack. Smurf attacks and others. Teardrop. A good DoS will knock a lot of Netware Servers offline in a Network as the constantly advertise their services. Anyhow Good Luck. Check that you have adequate power and look into BO and NetBus and the removers called Bo Freeze and NetBuster etc. It could also be any various number of problems the others have listed with cheap or bad ram or cheap mother brd or heat or your asking the processor and ram to do something it doesn't like. Write a Journal down of description and time of when each pc crashes or reboots. It once took an Hp or Ibm engineer two weeks to solve a rebooting problem on something like a mini, an AS400 I think and found after two weeks of studying the problem that one night a janitor walked in and pulled the plug and plugged in his floor waxer and when he was done plugged back in the AS400 and then was asked about how often he does that and the answer was about every two weeks. Anybody grinding or sawing on the same circuits? Or waxing the floor?
Good Luck!

by eto

I had three servers hooked up to one UPS that went bad. Everytime it did a self test, it rebooted the servers. Switched out the faulty battery and those three servers are not rebooting by themselves anymore. I would also suggest looking at memory or cpu. Maybe they're faulty.

But then again, check the O.S. Maybe it's a Microsoft thing.

by kishu_k

the problem may be with some of the system services....
I suggest u to check the devices option and the service startup sections....
Also take a look at the event viewer to consider any service failure....

if the system has a new device or any such thing configured recently try removing and then safely booting the system

by draco vulgaris

Ok, say I walk into the room and find a machine in the process of booting. Can the machine itself tell me if it is doing a cold or a warm boot?

by netman66

Yes, but u must catch it booting at a certain
time. Most machines upon a cold boot, u will
notice a memory test executing. On a warm
boot, this test is not done. That's how u
would know which boot is done. And if u don't
know; Cold boot - powercomputer off and on
Warm boot - use Ctrl+Alt+Del

by 2cherryz

Are you running any back office software like SMS?? I've seen scripted, forced software downloads or upgrades that cycle down workstations. As someone stated earlier, check your virus software configuration for auto updates(especially Mcafee!), and if so, check to see if is set to update locally or remotely. Uncheck this feature, and kill the script entry. Give it a whirl!!

by wbailey

I see some people posted re. power related issues. I actually have had the problem where a bad power supply caused my system to restart. I replaced the power supply and all has been well ever since. Additionally, if there is no UPS on the system andthe power source fluctuates (IE: surges/sags), the latest PC's tend to be very sensitive to this and could reboot. It is recommended to put PC's on good surge strips or UPS systems if building power is an issue.

Will

by dougm

I personally have seen this in windows systems.. It in my case has been a cpu overtemp condition caused by cpu cooler not working corectly..

hope this helps.

by user007

I have found that in Slot1 systems, if you reseat the processor (remove and replace) your reboot problems disappear.

Remember also not to bump the machine or move it around too much - it could loosen an expansion card of the CPU just enough to make the system unstable.

ATX power supplies are also buggy in this respect and a bump on the box can cause one of the pins on the M/B to loose contact with that of the Power supply and cause a hardware reset.

by vicki.laidlaw

Have you checked the NT machines to see if "Automatically Reboot" is checked on the Startup/Shutdown tab of System Properties? If that has been checked, every time NT encounters a system or driver problem which would otherwise cause a BSOD (Blue Screen of Death), the pc would simply reboot. I'm not sure if Windows 98 has this feature, but it's something to check out.

by reaching for stars

Hi Alex,

You need to be a little more specific about your problem. For instance, when these computers randomly reboot is it while running the same process? For example, does it seem to happen only when they access the internet? You also mentioneda few computers reboot. Did you add software or hardware to these particular machines but not the others? Have you added RAM to these PC's? Are the PC's running on UPS's? What kind of network are you running on? Are you using hubs? or coaxial cable with BNC connectors?

There are numerous reasons that could be causing your particular problem. If you can give us more information we may be able to help you identify what your problem is.

Linda

by morrow

If you are talking about a machine turning itself on from the Off position it can not be caused by a bad driver. It would more likely be the network card doing a wake on lan. I have seen this. It is told that it takes a particular string to wake on lan, I have found it to be not the case. If the particular machine is pinged with just a string of ***** it will likely wake. If you are not useing this feature I suggest that you disable it in the network card or remove the wake on lan cable in the computer. It will be the one that looks like a cd audio cable running from the NIC to the mother board. Hope this is some help.
Wade

by jheal

If you use reputable wake on LAN hardware, you will not have any random WOL events. The WOL string is the MAC add. repeated 16 times within one packet... Not going to happen by accident. With that said, disconnecting the WOL cable will work in cases where the power supply is not up to par, in systems that are PCI 2.0 or lower complient. In systems that are PCI 2.01 or better the WOL cable is not nessessary, and disconnecting it will make no diffence, the power is delivered via the PCI bus.
My expirence has been (I am Technical Supervisor for a system builder) that first you must be rid of any systems that use the 820 chipset with SDRAM, this chipset has a memory translation hub that converts the RDRAM design to a SDRAM design, and it turns out that its faulty. (I have had to change 200+ mainboards thanks to this). This fault will cause random reboots, and lock-ups. Next ensure that your power supplies are good. Then check RAM. The newest chipsets (810, 815, etc.) seem to be more sensitive to memory fualts, and tend to reboot if the RAM in it is not timed properly. RAM that worked perfectly well on a BX chipset may not work well on a 810, 815 based mainboard. If you did not build these systems yourself, you should have support from the manufacturer.

Hope this helps,

James M. Heal
Technical Supervisor - Bole Distributing Inc.
Intel Certified Integration Specialist - Networking

by crosbywa

Just in my past experaince as a tech, ive found that computers that reboot on thier own for no reason Either have a virus, Or the Power supply is going bad, in small cases it was the outlit that the computer was plugged into.

So try these series of test

1. Try a diffent power outlit for these computers.
2. virus scan
3. if Able to swap out the power supply so you can atlest test these,

W. A. Crosby

by toms

There are a lot of very good possible solutions posted, however most of them would seem to fit only 1 or 2 units doing this. My bet would be what happened in my shop, "surge protectors!". Those wonderful APC power strips were causing unexpected reboots on several machines after being in place for over 6 months. After a little research I found this to be a common but tough to find problem with non-battery back-up type surge protectors. Change out the strips on a suspect machine and see if that helps. It's a fairly cheap shotgun solution.
Good luck.....TomS

by alnine

How long have the computers been on. If it's been on for awile like say 3 hours our so. It may be do to a heat problem. CPU's that heat up tend to reboot themselves. Check to see if the fans are working inside the computer. Also check to see if any addon cards are overheating.This also could cause a system to reboot.

by wireguy

There's a Dell Windows 95 PC (OSR2) down the hall that reboots everytime you use Windows Explorer and access a network drive. You can access the network through "My Computer" or the command line with no problem, but do it in Explorer and it's like someone hits the reset button -- no blue-screen of death -- it just reboots. I'm tempted to reinstall Windows.

by rburnett

I have this seen this problem several times.
It was casued by crossed/damaged wiring in the network or serial cable. System will boot then right before the desktop appears PC will reboot repeating the same over and over. Unplug from network or unplug serial cable then boot. If it boots fine, problem is within cable connections not PC. Return response is garbled and resets Windows.

Randy

This discussion is closed to new replies.