Discussion Locked

Connectivity problem

0 helpful
10 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

We are using ScoutSync (same as Palm's Hotsync Server) to connect remote Palm IIIxe users via analog dial-up connection to our corporate database (RAS). At periodic intervals, we experience connectivity problems which result in an "Unknown" Owner showing up in the Scout Management Console and "Disconnected on date/time" as the Entry Text. The IP address is from a 3600 Cisco Router on our network which provides NAT, and we can see the connection authenticate at our firewall using Border Manager (Novell). Whenever the Firewall is reinitialized, this Unknown problem occurs. Although we can create the problem, we are unable to rectify it, nor can we predict how long the system will be down (hours to days) before it returns to normal. The remote user does pass through authentication at the Firewall but will not be authenticated at the Sync Server.

The routing within our network is as follows:
1. toll free phone number to 24 channel T1
2. T1 splits 16/8 at CSU, 16 lines going to aFax Server, 8 lines dedicated to Palm traffic
3. 8 lines go to 3600 Cisco Router which provides NAT
4. to switch A
5. to firewall - Novell, Border Manager, with Radius authentication - (NW5,sp5 & BM3,sp2 RADIUS 2.04)
6. to switch A
7. to switchB (different floor)
8. to Sync Server, ScoutSync Management Console (NT4,sp6)
9. to switch B
10. to Data Server (NT4, sp6; sql7, sp3)

10 replies

by dabutler

Lynne,

Thats a good one, - I am no expert, but did set up radius with an ascend box and had a problem on the NT domain controller where when the connection was broken, the default persistence length of the connection would not disconnect the connection of the logged in user. I would try to close the NT connection to the domain (I assume you are using Domain Authentication).. within 3 second of the user logging out. Good luck.

by jdbailey

I?m not sure what your problem is?

I?ll just provide a few comments ? maybe-help (then again) maybe-NOT?

Problem/s Symptoms: (1) The RAS experiences periodic connectivity problems. (2) Reinitializing the firewall causes an unknown problem and system outages. (3) At ScoutSync Management Console (Synsc-Server) a message is displayed ?Unknown? Owner ?Disconnected on date/time?.

Are these symptoms one, two, or three problems? One problem can have multiple symptoms, and vice-versa.

Did I put the problem symptoms in the correct sequence of events (123)?

The message appears when there are periodic (WHAT? sporadic/irregular or cyclic/regular) connectivity problems at the ?RAS???

Sporadic problem symptoms normally relate to userand/or intermittent hardware events that could help identify cause and solution.

Cyclic problem symptoms normally relate to software scheduled events that could help identify cause and solution.

Users can start a sporadic event, and then internal systems configuration and/or boot/diagnostics (normally cyclic/scheduled events) would appear as a sporadic event.

Could the Cisco Router that performs NAT for the RAS users be attempting to assign a new IP and reinitiate with the RAS the users? connection that is no longer present?

Is the connectivity problem between the T1 and RAS or the RAS and Router?

Is the firewall authenticating the router attempts to reestablish RAS connections that have been dropped?

Are guest logins, tokens, or passwords used at this point for authentication?

What is the firewall authenticating and how?

by jdbailey

You say, ?whenever the firewall is reinitialized the Unknown problem occurs.?

Why are you reinitializing the firewall? Does the RAS connectivity problem cause the firewall to lockup? Have you tried reinitializing switch-B or your ScoutSync serverto clear the problem? Are IPs for the RAS connections being automatically blacklisted on an ACL?

Your bottom line; ?remote user does pass through authentication at the Firewall, but will not be authenticated at the Sync-Server? suggest that everything is functioning correctly from the RAS up to and including the firewall. However, something appears to cause a conflict between what is being provided from switch-A to the Sync-server, and what the Sync-server is expecting is not being receivedfrom switch-A. Switch-A is providing accepted information from the firewall to the RAS user. Switch-A is providing firewall data to the Sync-server, but the Sync-server rejects the data provided, because ? (wrong data/format/protocol, unknown source/IP/user, ACL blacklist/settings, ? many more).

I don?t know what your problem is, but I hope the information I provided above will help you troubleshoot and resolve the problem. This is a very interesting problem. Bump me an email if you want some more of my comments on more problem information.

Jim

by estebandelatorre

Lynne,
I?ve saw very strange things on BorderManager when it is configured as a Internet Proxy + Firewall + NAT and trying VPN's remote access.
This happens to me when restaring the server and trying to log trough the VPN. Sometimes it works, sometimes it?s take too long to work!
So, try this.
REM the sentence like this:
REM SET NAT DYNAMIC MODE TO PASS THRU = ON
from the firewall's autoexec.ncf.
When the server finaly load EVERY service, EVERY volume, wait 5 minutes more and then load the line manually.

It works for me!!!
P.D.: I can?t find a "delay.nlm" do you have one?

edt@bancobgn.com

by lynne

Thanks, everyone, for your responses. It turns out that when other routers (& there were many) were added to the network, the routing tables on the firewall server were not updated. So, whenever the firewall server was reinitialized, it lost its routing tables and the packets would get to the sync table but wouldn't know how to find the way back to acknowledge. It took a packet sniffer software package plus three consultants to figure this out

This discussion is closed to new replies.