Discussion Locked

Create 10GB NT4 System Partition

0 helpful
5 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
Tell me what you think about this. I have found an odd way to Install NT4 onto any large size disk with one active partition. First start your install with Win2k, Create the partition max size and Format with NTFS. When the setup starts to copy files reboot and insert the NT4 set CD. Go thru the NT setup and select the already formatted partition and select to leave file system (NTFS) intact. It seems to work fine so far, but I am leary of "unsupported configuration" in my production environment. Give me your feedback.

5 replies

by lordinfidel

The only problem I can see is that 2K first formats using FAT32, then runs a conversion to NTFS v5.

NT4 can not read FAT32, and can not read NTFS v5 until SP4 or higher is applied.

At least that is the theory. I personally have not tried it.It might be able to read it, but I would be leary of it. If it seems like it is working, my only advice would then be to make sure that you apply SP4 or higher asap.

by kevin brown

I have done something similar using Drive Image. Applied NT Sp6 image to a 40 GB disk and had the image span the entire disk. NT will work perfectly until system files are updated or changed. Then there is a good chance the machine will not boot.

by lordinfidel

From boca?

Just checking... If it's not then never mind.

If it is, then hey what's up. It's mike morell (aka LordInfidel)

by mww1001

Some time ago, I mistakenly installed a NT SP6a image onto an 7.8 gig primary partition. One of my assistants "updated" the image to SP5, and the system crashed on next bootup. Message read "NTOSKernal not found". Took the drive, installed it as secondary drive in another system, could read all the \WINNT files, attributes, ACLs just fine, but it would not boot. Used a disk editor to move the file inside the 2 Gig partiton boundary, Bingo, bootup. Lesson learned - don't exceed 2 Gig on NT 4.0 System (MS meaning of word-System) partition. Made a convincer out of me. If your BOOT partition (again MS meaning of the word) is NOT the same as the System partition, NTOSKernal can be just about anywhere, at least in my experience. (SCSI drives don't seem to have that problem.)
One other neat little observation I've made in the past, if you have a drive with the PHYSICAL sectors at the head of the drive are bad. Make a small partition of 7 or 8 megabytes at the head using Partition Magic. Create another primary partition immediately after it. Format the first partition as FAT. Reboot the computer using a Win98 recovery disk. Use PQMagic on floppy and start it up, DELETE the first pgymy partition. Reboot on the WIN98 floppy, and continue your install of NT or WIN98. It will come up as bootable and the OS won't even know about the bad "front-steps" on the drive. This trick has worked with Seagate, Western Digital and Quantum drives.
BTW PQMagic and Drive Image are stellarproducts.

by shadowcat

OK I'm not sure how you did it. Resons behind this:

1: NT4 SP3 and earlier can only see 8GB of hardrive period!
2: I am unaware of any retail versions of NT4 with SP4 or above preinstalled.

Depending on what version of NT4 you have you should only be able to see 8 GB of Hardrive. there may actaully be a version of NT4 that is Post SP3 meaning that it can see more than 8 GB of Harddrive space.

If you want your boot/system partition to be NTFS on an IDE drive you will usually be limited to 8GB. Unless of course you have a version that is post SP3 then it will have the fix that makes it so the System can be much much larger.

Of course if someone then goes and installs a Service Pack that is an earlier version then the built in one you will run into problems like the previous person did.

I will have to believe that you have a post SP4 version of NT4 so that you can see the NTFS5 partition.

This discussion is closed to new replies.