Discussion Locked

Dell fails to activat ScanJet 5100C

0 helpful
7 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Have you seen this before? any suggestions?

If possible, could you send replies to my work email as well?
dhayden@elliott-turbo.com

I have a ScanJet 5100C that works on a couple of computers except a particular Dell Dimension.

What happens is the install goes fine. The hpppt tests the port as being fine but when I go to test the scanner or run a scan, the light never comes on and the application freezes.

My thought was that the parallel port is bad and not sending a signal on oneof the wires but the Dell technical support had me check out the port with a debug script and it seems ok.

I immediately took the scanner and cable over to the computer I took it off of and it worked fine, so moving it did not cause any damage.
We have also had printing problems with this computer in that, if you try to use an application while printing, the application and print would hang. Could only print again after a reboot. (hp deskjet printer)

Thanks
David S. Hayden

7 replies

by william jay

It may be silly for me to ask these, as the tech support likely did already but ...>, are the printer port setting in BIOS and in Windows set to EPP/Bidirectional, or to ECP or SPP or some other setting? Are the TEMP and TMP variables set properly ?Which DMA resources are used/available in Windows? After installation, did you completely power down, then power up the 5100 and then the computer? Please post a comment/update, and please wait before rejecting this answer just because you did thesethings already, as I will continue to assist until it works properly or the question is closed.

by Member 36022913

William,
Thank you for your help and additional information. Your last email was packed with good suggestions.

The problem has been taken out of my hands for the time being so I am closing the question.

by Member 36022913

Thanks William. I want to re check all of the items you listed. Actually, the Dell guy had me reset the CMOS to "default" which probably turned off the EPP/bi-directional and other settings. It is on my bosses computer so I have limited access. It will probably be next week before I can have at it again.

David

by Member 36022913

Just a side note MY ISP went out of business this weekend so the dhayden@haydenpub.com is not a valid address until Stargateinc.com gets my domain set up again. In the mean time I am using dshayden@stargate.net

by Member 36022913

William,
I had a false sense of hope for awhile. Upon reading your suggestions, as I was going through the devices, I noticed there was reference to a SCSI device for a different scanner. Tuns out my boss had previously installed an older HP scanner that used the scanner card.

I removed the scanner, the old card and uninstalled the software and started over. With high hopes I pressed the scanner button but alas the system froze up as before.

by Member 36022913

Here are the things I have tried as best I can remember them in the order I did them.

Installed scanner - installation failed
tried scanner on different computers it worked fine

uninstalled the scanner and all lpt drivers from problematic computer

reinstalled the lpt resources

reinstalled the scanner software and the scanner - installation failed

Called Dell, spent about half an hour on the phone with Dell support
- we reset the CMOS to its default settings
- we created a boot disk
- booted from the start disk into DOS
- ran a debug script to check out the parallel port - the port checked out ok

A couple of days later I tried again and discovered there was an old SCSI card left in the computer from a previous scanner
I removed the SCSI Scanner card

I edited the registry to remove all reference to scanners or the HP software

Removed and reinstalled the HP 5100C scanner - Installation failed

I installed a clean, formatted drive into a spare computerinstalled a fresh version of WIN 98

installed the scanner and software - Installation was successful

I installed and ran the Dell Diognostics from the Dell Disk - All aspects of the computer checked out ok

I took the new hard drive and replaced the Dell original drive

I loaded all the Dell resource and motherboard drivers from the Dell Disk

I installed the scanner on the clean drive with the fresh install of Win 98 - installation failed

This discussion is closed to new replies.