Question Locked

dell pe1800 cintinoussly beeps

0 helpful
10 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I have a dell pe1800 server with an OS(win2000 server) problem. I really need to get the data back on the hard disks because they were not backups. I removed the scsi hdds and in place of it i place another one so as to install another os on it, then try to access the initial hdds as we do on IDE hdds. However, when i hot plug the hdds, it was not seen, on the disk manager, i rescan for hard ware, this too did not work.
I then proceeded to remove, the harddisk and rebooted the machine. Though, it boots to windows desktop and it is working well, there's this continous beep from the system. I shut down the system ,removed all the scsi hard disks, and restarted the machine, but i still get the continous beep sound.
What could be the problem? How could it be solved?

secondly, i will need help on how to retrieve the data from the other scsi drives. I need assistance soonest!

Thanks

M ogodo

10 replies

by cmiller5400

Were the SCSI drives in an array (RAID5) before you pulled them out? If so, did you mark the order in which they were in the array set?

by bams lele

Thanks for your response. The keyboard is okay. My observation when the system is booting is that the beeping starts as soon as the hard disk (scuzzy) are being checked. the beeping continues after the system's boots to the desktop. Note: in my initial post, i said i removed the scuzzy hdd physically because the system was not recognizing it, and re fixed it. when i reboot, the beeping sound began.
I need help on the cause of this and how to stop this

by bams lele

Thans for your response.
No; they were not in an array set. I actually did the installation on a single SCSI HDD. The problem was that the initial SCSI HDD on the machines were what i want to back up, and since they were not sensed by the CPU, i decided to pull it out and re fix it. After that, the system starts beeping when the boot process gets to the portion where the hard disks are being checked. This beeping continues to the desktop and remains till one shut down the machine. I really want to know how to turn off this beeping...

by bams lele

Thank you cmiller5400 for the link... to dell's support. The beeping challenge has been resolved! Many thanks to you.
Now, i want to see if i could salvage the data in the initial two SCSI disks on the pe1800. I added both to the server after installing the OS on another two SCSI disks, used the disk management utility to rescan disks. But I observed that it is not detecting the hardware.
my question now is;

how can one access the data on both initial disks (mirror). What hardware configuration must i do since the use of the disk management utility seem not to help?

NOte: The fault with the initial disks is OS. This could not be repaired. But the data need to be recovered

Thanks for your help.

by rahouseholder

Just a thought, but what SCSI IDs are the drives set for? Did you change the jumpers on the old drives after installing the new ones? Haven't messed with SCSI drives lately, so as far as I know, they could be jumperless now....

by bams lele

Thanks for the contribution. The drives are jumperless. What i will add is this: they were initially on bay 1 and 2 but now on bay 4 and 5. This is so because the drives i re inatalled the OS on are on bay 1 and 2 respectively.
many thanks once again!

by bams lele

Thanks for the contribution. The drives are jumperless. What i will add is this: they were initially on bay 1 and 2 but now on bay 4 and 5. This is so because the drives i re inatalled the OS on are on bay 1 and 2 respectively.
many thanks once again!

This discussion is closed to new replies.